This article explains how to use the ABBINATO 2013 by Boretti.
About the temperature controls – Profile Models. Not all features are on all models. Your controls will look like one of the following: NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not removed during installation, remove it now. The temperature controls are preset in the factory at 37°F (3°C) for the refrigerator compartment and 0°F (-18°C) for the freezer compartment. Allow 24 hours for the temperature to stabilize to the preset recommended settings. Refrigerator temperatures can be adjusted between 34°F and 46°F (1°C to 8°C), and the freezer temperatures can be adjusted between –6°F and +8°F (–21°C to –13°C). To change the Refrigerator temperature: LCD Models: Access By: Home > Refrigerator Activate By: Using the arrows to select the desired temperature. You must press ENTER to set the new temperature. To change the Freezer temperature: Access By: Home > Freezer Activate By: Using the arrows to select the desired temperature. You must press ENTER to set the new temperature. Once the desired temperature has been set, the display will return to the HOME screen and show the set temperatures underneath the actual temperature display for several seconds. Several adjustments may be required. Each time you adjust the controls, allow 24 hours for the refrigerator to reach the temperature you have set. Non-LCD Models: To change the temperature, press and release the FREEZER TEMP/FRIDGE TEMP pad. The SET light will come on and the display will show the set temperature. To change the temperature, tap either the or pad until the desired temperature is displayed. Once the desired temperature has been set, the temperature display will return to the actual refrigerator and freezer temperatures after 5 seconds. Several adjustments may be required. Each time you adjust the controls, allow 24 hours for the refrigerator to reach the temperature you have set. The temperature controls can display both the SET temperature as well as the actual temperature in the refrigerator and freezer. The actual temperature may vary slightly from the SET temperature based on usage and operating environment. Turning the cooling system off: LCD models: Turning the cooling system OFF stops cooling in both the freezer and refrigerator compartments, but does not shut off electrical power to the refrigerator. LCD Models: Access By: Home > Options > Information and Settings > Cooling System Off To turn the cooling system back on, press the touch screen and press the ON button. Activate By: Pressing ENTER. Non-LCD Models: Press and release the FREEZER TEMP/FRIDGE TEMP pad. Press to set freezer temperature to 5. The display will show OFF. To turn the unit back on, press the FREEZER TEMP/FRIDGE TEMP pad. Press to set the freezer and refrigerator temperatures to the preset points of 0°F (-18°C) for the freezer and 37°F (3°C) for the refrigerator. When the unit is turned back on, it will take up to 24 hours to stabilize. LCD Models: Units The LCD models are shipped from the factory with default settings of English units. To change to Metric units, select: Home>Options>Information and Settings>Settings>Units Metric/English>Metric. To change back to English units repeat the above steps and select English at the final step. NOTE: The help screen has default setting for US and Canada customers. If you need replacement parts, contact your local distributor. About the temperature controls – GE, Monogram Models. The unit will have one of the temperature controls shown below: The temperature controls are preset in the factory at 5 for both the refrigerator and freezer compartments for the Set Point Controls or to 3/-18ºC for Actual Temp Controls. To adjust the Set Point temperature, press the WARMER or COLDER button on either the Freezer or Refrigerator side. The set point light will come on. Press WARMER or COLDER until the desired setting is reached. To adjust the Actual Temp temperature, first press the Freezer or Refrigerator button. Then press the or buttons (or the or ) to increase or decrease temperature to the desired setting. Repeat for the other compartment. Several adjustments may be required. Each time you adjust controls, allow 24 hours after each adjustment for the refrigerator to reach the setting you have selected. Setting either or both controls to 0 stops cooling in both the freezer and refrigerator compartments, but does not shut off electrical power to the refrigerator. Control settings will vary based on personal preferences, usage and operating conditions and may require more than one adjustment. NOTE: The refrigerator is shipped with protective film covering the temperature controls. If this film was not removed during installation, remove it now. This refrigerator is designed to operate in ambient temperatures specified by its Temperature Class, which is marked on the rating plate. Temperature Class Symbol Ambient Temperature Maximum Minimum Extended Temperate SN 32°C 10°C Temperate 32°C 16°C Subtropical ST 38°C 16°C Tropical 43°C 16°C NOTE: Internal temperature may be affected by such factors as the location of the refrigerator, ambient temperature and frequency of door openings. Adjust temperature controls as required to compensate for these factors. About TurboCool.™ How it Works TurboCool™ rapidly cools the refrigerator compartment in order to more quickly cool foods. Use TurboCool when adding a large amount of food to the refrigerator compartment, putting away foods after they have been sitting out at room temperature or when putting away warm leftovers. It can also be used if the refrigerator has been without power for an extended period. Once activated, the compressor will turn on immediately and the fans will cycle on and off at high speed as needed for eight hours. The compressor will continue to run until the refrigerator compartment cools to approximately 34°F (1°C), then it will cycle on and off to maintain this setting. After 8 hours, or if TurboCool is pressed again, the refrigerator compartment will return to the original setting. How to Use LCD Models: Access By: Home > Options > Refrigerator Options > TurboCool Activate By: Pressing ON. Deactivate By: Pressing OFF. Non-LCD Models: Press SET FEATURES. The refrigerator temperature display will show TurboCool and/or TC. Press ON/OFF. Internal Control Models: Press TurboCool. The TurboCool indicator light will come on. After TurboCool is complete, the TurboCool indicator light will go out. After TurboCool is complete, the refrigerator compartment will return to the original setting. NOTES: The refrigerator temperature cannot be changed during TurboCool. The freezer temperature is not affected during TurboCool. When opening the refrigerator door during TurboCool, the fans will continue to run if they have cycled on. About ClimateKeeper2.™ (on some models) How it Works The ClimateKeeper2™ is the industry’s most advanced refrigeration system, delivering optimum temperature and humidity performance to keep food garden fresh longer and reduce freezer burn, while maintaining efficiency. The ClimateKeeper2 system features two evaporators—one for the refrigerator and one for the freezer. This provides two separate cooling systems, and separates the airflow between the fresh food and freezer compartments during normal cooling operations.* This ensures that the humidity levels in the fresh food compartment are significantly higher than in a conventional system,** allowing fresh produce and other unsealed foods to retain their moisture content and freshness longer. Moisture sensitive foods such as fresh fruit, salads, rice, etc., can now be stored on open shelves without excessive moisture loss. Due to the higher humidity in the refrigerator, you may on occasion experience fog or small amounts of moisture in the refrigerator compartment. This is normal and may come and go as different food loads and environmental conditions change. Wipe dry with a paper towel if desired. The separate airflow system minimizes the mixing of air between the two compartments, which reduces fresh food odor transfer to improve the taste of ice. The ClimateKeeper2 system also reduces the number of defrosting cycles in the freezer evaporator, thereby reducing freezer burn.
*Freezer air is used in the CustomCool feature.
**Testing shows a higher level of humidity in the Fresh Food section in ClimateKeeper2 refrigerators versus conventional units. About Set Features. This pad is used to select the following features: TurboCool, Quick Ice, Door Alarm and Water Filter. Pressing SET FEATURES repeatedly will cycle through all of the available features and then exit the mode. If no key is pressed, the mode will exit and return to displaying features currently set. About CustomCool™. (on some models) How it Works The CustomCool™ feature is used to quickly chill items, thaw items or hold the pan at a specific temperature. This feature is a system of dampers, a fan, a temperature thermistor and a heater. The pan is tightly sealed to prevent temperature fluctuations in the rest of the refrigerator. The controls for this pan are located on the dispenser with the temperature controls. How to Use Empty the pan. Place the Chill/Thaw tray in the pan. Place the items on the tray and close the pan completely. LCD Models: Access by: Home > Options > Refrigerator Options > CustomCool Pan Non-LCD Models: Select the ExpressThaw™, ExpressChill™ or SelectTemp™ pad. The display and SET light will come on. Tap the pad until the light appears next to the desired setting. Use the following chart to determine the best setting to use. ■ ExpressChill can be set to 15, 30 or 45 minutes. The default is 15 minutes. ■ To stop a feature before it is finished: For LCD Models: Go into that feature’s menu and press the OFF button. For Non-LCD Models: Tap that feature’s pad until no options are selected and the display is off. ■ During ExpressThaw and ExpressChill, the display on the controls will count down the time in the cycle (on some models). ■ After the ExpressThaw cycle is complete, the pan will reset to the MEAT setting (32°F [0°C]) to help preserve thawed items until they are used. ■ The displayed actual temperature of the CustomCool pan may vary slightly from the SET temperature based on usage and operating environment. NOTE: For food safety reasons, it is recommended that foods be wrapped in plastic wrap when using ExpressThaw. This will help contain meat juices and improve thawing performance. How to Remove and Replace the Drawer To remove: Pull the drawer out to the stop position. Rotate all four swing locks to the unlock position. Lift the front of the drawer up and out. To replace: Make sure all four swing locks are in the unlock position. Place the sides of the drawer into the drawer supports, making sure the swing locks fit on the drawer slots. Lock all four swing locks by rotating them to the lock position. About CustomCool™. (on some models) CustomCool™ Chart NOTE: Results may vary depending on packaging, starting temperature and other food traits.
■ Hamburgers (0.25 kg) ■ Individually Wrapped Filet Mignon (0.25 kg)
kg (8 hours)
■ Chicken Breasts (0.5 kg) ■ Minced Beef (0.5 kg) ■ Steak (0.5 kg)
kg (10 hours)
■ Chicken Breasts (1.0 kg) ■ Minced Beef (1.0 kg) ■ Steak (1.0 kg)
kg (12 hours)
■ Chicken Breasts (1.50 kg) ■ Minced Beef (1.50 kg) ■ Steak (1.50 kg) 15 Minutes ■ 1 Beverage Can (355 ml) ■ 2 Small Juice Boxes (175–240 ml each) 30 Minutes ■ 2 to 6 Beverage Cans (355 ml each) ■ 2 Plastic 590 ml Bottles of Beverage ■ 4 to 6 Small Juice Boxes (175–240 ml each) ■ 3 Foil Juice Packets ■ Wine (750 ml bottle) 45 Minutes ■ 2 Liter of Beverage ■ 1.9 Liters of Juice ■ Gelatin–1 package Citrus Setting (6°C) ■ Oranges, Lemons, Limes, Pineapple, Cantaloupe ■ Beans, Cucumbers, Tomatoes, Peppers, Aubergine, Squash Produce Setting (1°C) ■ Strawberries, Raspberries, Kiwifruit, Pears, Cherries, Blackberries, Grapes, Plums, Nectarines, Apples ■ Asparagus, Broccoli, Corn, Mushrooms, Spinach, Cauliflower, Kale, Green Onion, Beetroot, Onions Meat Setting (–1°C) ■ Raw Meat, Fish and Poultry Some CustomCool models feature a beverage center. It is designed to store beverages at colder temperatures. Select this feature if you like to keep extra-chilled refreshments on hand. How to Use the Beverage Center (LCD models only) Access by: Home > Options > Refrigerator Options > Beverage Center Activate by: Pressing ON. Deactivate by: Pressing OFF. To remove: Remove dairy bin first. Holding the bottom of the dairy bin, lift the front straight up, then lift up and out. Holding left and right side of beverage center, lift straight up and out. Leave adapter in place. To replace: Engage backside of beverage center in molded supports on adapter. Then push down on the sides of the beverage center. The beverage center will lock into place. Replace dairy bin. Dairy Bin How to Remove and Replace the Beverage Center (LCD models only) Adapter Beverage Center About the water filter. The water filter cartridge is located in the back upper right corner of the refrigerator compartment. When to Replace the Filter LCD Models: A pop-up screen will appear on the LCD screen to remind you to replace the water filter. You can check the status of the water filter manually. Access By: Home > Options > Dispenser Options > Reset Water Filter Non-LCD Models/External Controls: There is a replacement indicator light for the water filter cartridge on the dispenser. This light will turn orange to tell you that you need to replace the filter soon. The filter cartridge should be replaced when the replacement indicator light turns red or if the flow of water to the dispenser or icemaker decreases. Removing the Filter Cartridge If you are replacing the cartridge, first remove the old one by slowly turning it to the left. Do not pull down on the cartridge. A small amount of water may drip down. Installing the Filter Cartridge There is an adapter attached to the top of the new filter cartridge. The adapter must be removed before installing the cartridge. To remove the adapter, turn it to the left about 1/4 turn. Fill the replacement cartridge with water from the tap to allow for better flow from the dispenser immediately after installation. Line up the arrow on the cartridge and the cartridge holder. Place the top of the new cartridge up inside the holder. Do not push it up into the holder. Slowly turn it to the right until the filter cartridge stops. DO NOT OVERTIGHTEN. As you turn the cartridge, it will automatically raise itself into position. The cartridge will rotate about 1/2 turn. Run water from the dispenser for 5 minutes to clear the system and prevent sputtering. LCD Models: Press FILTER REPLACED button to confirm replacement. Non-LCD Models: Press the SET FEATURES pad until REPLACE WATER FILTER is lit. Press and hold the ON/OFF pad for 3 seconds. WATER FILTER IS RESET will show in the window. NOTE: A newly installed water filter cartridge may cause water to spurt from the dispenser. Filter Bypass Plug You must use the filter bypass plug when a replacement filter cartridge is not available. The dispenser and the icemaker will not operate without the filter or filter bypass plug. Replacement Filters: To order additional filter cartridges, contact your local distributor. About the refrigerator doors. Refrigerator Doors The refrigerator doors may feel different than the ones you are used to. The special door opening/closing feature makes sure the doors close all the way and are securely sealed. When opening and closing the door you will notice a stop position. If the door is opened past this stop point, the door will remain open to allow you to load and unload food more easily. When the door is only partially open, it will automatically close. The resistance you feel at the stop position will be reduced as the door is loaded with food. When the door is only partially open it will automatically close. Beyond this stop the door will stay open. About the shelves and bins. Not all features are on all models. Refrigerator Door Bins and Freezer Door Tilt-Out Bins Large Bins The larger refrigerator door bins and freezer tilt-out door bins are adjustable. To remove: Lift the front of the bin straight up, then lift up and out. To replace or relocate: Engage the back side of the bin in the molded supports of the door. Then push down on the front of the bin. Bin will lock in place. Small Bins To remove: Lift the front of the bin straight up then out. To replace: Position the bin above the rectangular molded supports on the door. Then slide the bin down onto the support to lock it in place. The snugger helps prevent tipping, spilling or sliding of small items stored on the door shelf. Place a finger on either side of the snugger near the rear and move it back and forth to fit your needs. Refrigerator bin Freezer tilt-out bin Snugger Bottle Retainer The bottle retainers are adjustable and keep tall items from tipping over. To remove: Lift the front of the retainer straight up, then lift it up. To replace or relocate: Engage the back of the bottle retainer in the molded supports on the door. Then push down on the front of the bottle retainer. Bottle retainer About the shelves and bins. Slide-Out Spillproof Shelf The slide-out spillproof shelf allows you to reach items stored behind others. The special edges are designed to help prevent spills from dripping to lower shelves. To remove: Slide the shelf out until it reaches the stop, then press down on the tab and slide the shelf straight out. To replace or relocate: Line the shelf up with the supports and slide it into place. The shelf can be repositioned when the door is at 90° or more. To reposition the shelf, slide the shelf past the stops and angle downward. Slide shelf down to the desired position, line up with the supports and slide into place. Make sure you push the shelves all the way back in before you close the door. Press tab and pull shelf forward to remove QuickSpace™ Shelf This shelf splits in half and slides under itself for storage of tall items on the shelf below. This shelf can be removed and replaced or relocated just like Slide-Out Spillproof Shelves. On some models, this shelf can not be used in the lowest position. Removable Beverage Rack The beverage rack is designed to hold a bottle on its side. It can be attached to any slide-out shelf. To install: Line up the large part of the slots on the top of the rack with the tabs under the shelf. Then slide the rack back to lock it in place. 1 2 Door Beverage Rack (on some models) This rack holds up to 5 cans. The rack hangs from the sides of the dairy bin. To remove: Empty the wine/beverage rack. Holding the bottom of the dairy bin, lift the front straight up, then lift up and out. To detach the rack from the dairy bin, pull the rack’s side wires out of the holes on each side of the dairy bin. To replace: Reattach the rack to the sides of the bin. Engage the back side of the bin in the molded supports on the door. Then push down on the front of the bin. The bin will lock into place. About the shelves and bins. Deep Freezer Baskets To remove, push the basket all the way to the back of the freezer. Lift up until the back pins are disengaged. Lift the entire basket up and pull out. The divider can be used to organize food packages. For large packages, simply fold down the divider. Make sure you push the baskets all the way back in before you close the door.
⚠ WARNING: Poor performance may occur if freezer baskets are not used. Storage of items in the freezer without using baskets may result in poor temperature performance due to restrictions of air flow within the freezer compartment. Freezer Baskets To remove, slide out to the stop position, lift the front past the stop position and slide out. Make sure you push the baskets all the way back in before you close the door. WARNING: Poor performance may occur if freezer baskets are not used. Storage of items in the freezer without using baskets may result in poor temperature performance due to restrictions of air flow within the freezer compartment. Divider Fixed Freezer Shelves There are two types of fixed freezer shelves. To remove this type of shelf: Lift the shelf up at the left side. Bring the shelf out. To remove this type of shelf: Lift up the left side of the shelf and slide it left into the center of the shelf supports. Rotate the right side of the shelf up and out of the shelf supports. About the freezer compartment. Loading the Freezer Compartment Load so that at least 15 mm of space remains clear between stacks of packages and 15 mm to 25 mm of space between the top of any stack and any shelf or basket above it. Packages may hang over the front of shelves but must remain 15 mm from doors. ■Food to be frozen must not be placed in direct contact with food in storage. If food is to be frozen every day, it may be necessary to reduce the quantity to be frozen. ■If a quantity of food needs to be frozen, set the freezer control to its coldest setting. After the food is frozen, reset the freezer control to its initial position. ■Food is most quickly frozen on the middle three shelves of the freezer compartment and most slowly in the freezer door shelves. ■Do not store commercially quick-frozen food longer than the time recommended by the food manufacturers. ■If the power to the appliance is shut off for an extended time or if the refrigerating system fails, do not open the doors unless absolutely necessary. When it is necessary, close them as quickly as possible so the frozen food will stay frozen as long as possible. ■The freezer door storage shelves marked with a two-star label are only appropriate for the storage of previously frozen food. Effervescent drinks should not be stored in the freezer compartment. Freezer Performance This Refrigerator/Freezer has an overall “Four Star” rating. Freezer performance is classified by star ratings defined by ISO 15502 STANDARD AND SUMMARY BELOW: CODE FREEZING–LOAD TEMP. (FOOD TEMPERATURE) Below –6°C. Below –12°C. Below –18°C. About the crispers and pans. Not all features are on all models. Fruit and Vegetable Crispers Excess water that may accumulate in the bottom of the drawers should be wiped dry. On some models the bottom drawer has a cover that slides back as the drawer is opened. This allows full access to the drawer. As the drawer is closed, the cover will slide forward into its original position. Adjustable Humidity Crispers Slide the control all the way to the (high) setting to provide high humidity recommended for most vegetables. Slide the control all the way to the (low) setting to provide lower humidity levels recommended for most fruits. Convertible Meat Pan The convertible meat pan has its own cold air duct to allow a stream of cold air from the freezer compartment to flow to the pan. The variable temperature control regulates the air flow from the Climate Keeper.™ Set the control to the (coldest) setting to store fresh meats. Set the control to (cold) to convert the pan to normal refrigerator temperature and provide extra vegetable storage space. The cold air duct is turned off. Variable settings between these extremes can be selected. Crisper Removal The top crispers can easily be removed by pulling the drawer straight out and lifting the drawer up and over the stop location. If the door prevents you from taking out the drawers, first try to remove the door bins. If this does not offer enough clearance, the refrigerator will need to be rolled forward until the door opens enough to slide the drawers out. In some cases, when you roll the refrigerator out, you will need to move the refrigerator to the left or right as you roll it out. To remove the bottom crisper: Pull the drawer out to the stop position. Rotate all four swing locks to the unlock position. Lift the front of the drawer up and out. To replace the bottom crisper: Make sure all four swing locks are in the unlock position. Place the sides of the drawer into the drawer supports, making sure the swing locks fit on the drawer slots. Lock all four swing locks by rotating them to the lock position. About the automatic icemaker. A newly-installed refrigerator may take 12 to 24 hours to begin making ice. Automatic Icemaker The icemaker will produce seven cubes per cycle–approximately 100–130 cubes in a 24-hour period, depending on freezer compartment temperature, room temperature, number of door openings and other use conditions. To access the icemaker: Pull the shelf above the ice drawer straight out. Always be sure to replace the shelf. If the refrigerator is operated before the water connection is made to the icemaker, set the power switch in the O position. When the refrigerator has been connected to the water supply, set the power switch to the l position. You will hear a buzzing sound each time the icemaker fills with water. The icemaker will fill with water when it cools to – 10°C. A newly-installed refrigerator may take 12 to 24 hours to begin making ice cubes. Throw away the first few batches of ice to allow the water line to clear. Be sure nothing interferes with the sweep of the feeler arm. When the bin fills to the level of the feeler arm, the icemaker will stop producing ice. It is normal for several cubes to be joined together. If ice is not used frequently, old ice cubes will become cloudy, taste stale and shrink. If ice cubes get stuck in the icemaker, the green power light will blink. To correct this, set the power switch to O and remove the cubes. Set the power switch to I to restart the icemaker. After the icemaker has been turned on again, there will be a delay of about 45 minutes before the icemaker resumes operation. NOTE: In homes with lower-than-average water pressure, you may hear the icemaker cycle multiple times when making one batch of ice. Pull the upper freezer shelf straight out to access the icemaker. Always be sure to replace the shelf. The shelf can be used for storage. NOTE: In 25BIS Models, the ice bin is suitable for the storage of ice only. Power Switch Icemaker Feeler Arm Green Power Light Shelf Ice Drawer WARNING:Connect to potable water supply only. Installation of the icemaker must be done by a qualified service technician. Special note about ClimateKeeper2™ dispenser models: ■Dispenser models have a tilt-out ice bin. The bin can be tilted out as shown in the illustrations, and it will hold itself up while you take ice out or turn the icemaker power switch on and off. Be sure to put the bin back in place before closing the door. ■To restore your ice level from an empty bucket stage, the following steps are recommended: 12 hours after the first batch of ice has fallen into the bin, dispense 3 to 4 cubes. After an additional 6 hours, dispense 3 to 4 cubes again. These steps will restore your ice level in the shortest amount of time. Lift the bin, then pull it forward until the bin stops. Lower the bin to access ice or reach the power switch. NOTE: In order to take full advantage of the tilt-out ice bin, only store items on the shelf below the ice bin that are no taller than the lowest point on the bin. On dispenser models with a tilt-out ice bin, to access ice or reach the power switch: Ice Storage Drawer To access ice, pull the drawer forward. To remove: Set the icemaker power switch to the O (off) position. Pull the drawer straight out and then lift past the stop position. To replace: When replacing the drawer, be sure to press it firmly into place. If it does not go all the way back, remove it and rotate the drive mechanism 1/4 turn. Then push the drawer back again. Ice Drawer Rotate Drive Mechanism About the ice and water dispenser. (on some models) To Use the Dispenser Select CUBED, CRUSHED or WATER. Press the glass gently against the top of the dispenser cradle. The spill shelf is not self-draining. To reduce water spotting, the shelf and its grille should be cleaned regularly. If no water is dispensed when the refrigerator is first installed, there may be air in the water line system. Press the dispenser arm for at least two minutes to remove trapped air from the water line and to fill the water system. To flush out impurities in the water line, throw away the first six glassfuls of water. CAUTION: Never put fingers or any other objects into the ice crusher discharge opening. Locking the Dispenser Press the LOCK or LOCK CONTROLS pad for 3 seconds to lock the dispenser and control panel. To unlock, press and hold the pad again for 3 seconds. Spill Shelf Quick Ice When you need to speed up ice production, use the Quick Ice feature. While this feature is turned on, the freezer fan runs continuously for 48 hours, or until the feature is turned OFF. During this period, ice production will increase up to 40%. Models with the integrated ice feature system require at FIRST USE at least half an 8 oz. glass of ice to be dispensed every 6 to 12 hours. This will help the icemaker fill the bucket properly so that dispensing is better. Dispenser Light The LIGHT pad turns the night light in the dispenser on and off. The light also comes on when the dispenser cradle is pressed. On some models, if this light burns out, it should be replaced with a 6 watt 12V maximum bulb. Door Alarm Use Door Alarm to sound if either door is open for more than 3 minutes. The alarm will stop once the door is closed. For LCD models, a popup screen will appear. The alarm can be silenced by touching the LCD screen. LCD Models: Access By: Home > Options > Information and Settings > Settings > Door Alarm Access By: Pressing ON. Deactivate By: Pressing OFF. Non-LCD Models: Press the SET FEATURES pad once and DOOR ALARM will blink. Press ON/OFF and the door alarm will be set and the icon will turn solid. Press ON/OFF again to turn the alarm off. How to Use LCD Models: Access by: Home > Options > Freezer Options > Quick Ice Activate by: Pressing ON. Deactivate by: Pressing OFF. Non-LCD Models: Press the SET FEATURES pad twice and QUICK ICE will blink. Press ON/OFF to turn the feature on, then again to turn it off. Precise Fill (on some models) This water dispenser is equipped with a feature called “precise fill.” This feature allows you to choose a precise amount of water (cups or ounces) that you would like dispensed. Pints and Liters are also available for LCD models. LCD Models Access By: Home > Options > Dispenser Options > Precise Fill > Set Amount Activate By: Using the arrow buttons to select the desired amount. Press MORE UNITS to select between CUPS, OUNCES, PINTS or LITERS. Non-LCD Models Press the PRECISE FILL CUPS/OZ pad. The WATER pad will light and the CRUSHED and CUBED ice pads will turn off. The last unit used will be displayed. Press the PRECISE FILL pad again to toggle between cups and ounces. If you selected OUNCES, press the or pad to select the number of ounces you would like to have dispensed between 2–99 ounces. The default is 8 ounces. If you selected CUPS, press the or pad to select the amount you would like to have dispensed. They are displayed as 0.25, 0.33, 0.5, 0.66 and 0.75, with the highest amount being 9.75 cups. The default is 1 cup. For liters, the amounts are displayed as 0.05 to 2.25 in increments of 0.05. Press the cup against the cradle and water will begin dispensing. It will automatically stop when the amount set has been dispensed. The display will show the amount of water dispensed, beep, then reset after 5 seconds. NOTE: Do not leave the dispenser unattended when water is being dispensed. If you would like to stop dispensing water before the specified amount has been dispensed, just remove the cup from the cradle. The display will show the amount that has been dispensed for 5 seconds. If the cup switch is pressed again within that time, the dispenser will continue up to the set amount. If not, the display will return to the set amount. > > > > Cleaning the Outside The dispenser drip area, beneath the grille, should be wiped dry. Water left in this area may leave deposits. Remove the deposits by adding undiluted vinegar to the well. Soak until the deposits disappear or become loose enough to rinse away. The dispenser cradle. Before cleaning, lock the dispenser by pressing and holding the LOCK or LOCK CONTROLS pad for 3 seconds. Clean with warm water and baking soda solution—about a tablespoon (15 ml) of baking soda to a quart (1 liter) of water. Rinse thoroughly and wipe dry. The door