This article contains the manual for the EL 145 by Boretti.
2. DISPLAY
Symbols indicating functions in progress: duration and manual function = pot symbol automatic programme = "A" Minute minder = bell symbol
3. SETTING A FUNCTION
Select the function required by pressing the corresponding button and set the time with the +/- buttons.
4. LEGEND FOR BUTTONS
Bell button
Cooking time button
End of cooking button
- + button = timer settings Time is increased with the "+" button and decreased with the "-" button at a speed directly proportional to the length of time for which the button is pressed.
5. CLOCK FUNCTION
The clock function is activated by pressing the cooking time, and end of cooking buttons simultaneously. The time is set by pressing the +/- buttons. Any previously set programmes will be automatically cancelled.
6. MANUAL FUNCTION
This function is set by pressing the cooking time, and end of cooking buttons simultaneously. The symbol "A" disappears and the pot symbol appears. Previously set programmes are cancelled.
7. SEMI-AUTOMATIC FUNCTION WITH COOKING TIME
Select the cooking time function (button) and set the time with the +/- buttons. The symbols "A" and the pot symbol appear. The oven is switched on. When the time coincides with the set time, shown on the end of cooking button, the oven is switched off and the pot symbol disappears. The buzzer then sounds. The symbol "A" starts to flash.
8. SEMI-AUTOMATIC FUNCTION WITH END OF COOKING TIME
Choose the function end of cooking (button) and set the final time with the +/- buttons. The symbols "A" and the pot symbol appear. The oven is switched on. When the time coincides with the set time the oven is switched off and the pot symbol disappears. The buzzer then sounds. The symbol "A" starts to flash.
9. AUTOMATIC FUNCTION WITH COOKING TIME AND END OF COOKING
Choose the function cooking time and set the required time with the +/- buttons. The symbol "A" appears. The oven is switched on and the pot symbol appears. Wait a few seconds until the current time appears. Set the end time using the end of cooking button. the approximate final time appears on the display. Use the +/- buttons to set the final time actually required. The oven is switched off and the pot symbol disappears. The pot symbol will appear again when the time coincides with the final time minus the cooking time. At the end of the automatic programme the symbol "A" starts to flash. The buzzer sounds and the oven and pot symbol disappear.
10. MINUTE MINDER
Choose the timer function (button) and set the required time with the +/- buttons. The bell symbol will remain on for the duration of time set. At the end of this time the buzzer sounds.
11. BUZZER
The buzzer sounds at the end of the cooking time function and continues to buzz for 7 minutes. The buzzer is silenced by pressing any of the buttons or. The volume of the buzzer can be adjusted using the "-" button without having first selected any function. There are three different buzz volumes to choose from and their duration depends upon the length of time for which the "-" button is held pressed.
12. START OF A PROGRAMME AND CHECKING
Once a programme has been selected it starts after setting the time. The time remaining can be viewed at any time by selecting the corresponding function again.
13. IDENTIFYING A PROGRAMMING ERROR
There is a programming error if the time indicated on the clock is between the cooking and end of cooking times. The error is indicated by the buzzer sounding and the symbol "A" flashing.
14. CANCELLING A PROGRAMME
To cancel a programme select the manual function. At the end of the set programme this is automatically cancelled.
15. IMMEDIATE USE
A) If the display flashes read point B, otherwise go to point C. B) If the display flashes the correct time has not been set or there has been a power failure. In this case, set the correct time (see paragraph 5) and then go to point C. C) Press the and button simultaneously. Set the temperature (thermostat knob) and function (selector knob) using the knobs on the appliance.
16. COOKING WITH PROBE
When the oven is cold, insert the probe in the food and the plug in the connecting bush on the left inside wall of the oven. 2 numbers appear on the display. The number on the left indicates the probe temperature. The number on the right indicates the programmed temperature, which can be set using the + and - keys. When the programmed temperature is reached the oven switches off and you will hear an acoustic warning which you can silence by pressing any key on the programmer. Disconnect the probe from the oven only when the oven is cold. The probe has a range of action of 0 to 99°C, see the respective cooking table.