This article explains how to assemble the BKVD-179 by Boretti.
It is recommended that this installation be performed by authorized technical stuff. ! Before installation, read the instructions carefully. ! Fit the refrigerator/freezer in stable kitchen units only. ! If necessary, reverse the door according to instructions.
2. Open the package. Take gasket spacer and brake into three as shown in figure.D. The middle part is door hang rail®. The other two parts are unit door spacers®. (fig.D)
3. Insert trim flap into slot and screw by screws®. (fig.E)
4. Pass the power cord through ventilation shaft and position it so that the appliance could be easily plugged in once it has been installed. (fig.B - fig.C)
5. Cut trim gasket to the height of the recess and stick it on reverse side of the door hinges of the appliance. (fig.E)
6. Raise the appliance and slide into the kitchen unit.
7. Lean the appliance to the kitchen unit through the hinges and align the front feet with front surface of the kitchen unit. (fig.F)
8. Open the appliance doors and screw the front feet by using screws. (fig.G)
9. Screw trim flap to kitchen unit using screws. (fig.G)
10. Screw the hinges to the kitchen unit using screws. (fig.G)
11. Close the appliance doors. Unscrew and take out the nuts, washers and adjustment bolts from the appliance upper door®. (fig.H)
12. Take out the liners of the tapes on door hang rails®. Place door hang rails on the appliance upper door® by inserting the bosses on the holes of the appliance upper door, aligning the front surfaces of the door hang rails® and appliance door parallel. Let the door hang rails stick onto the appliance upper door®. (fig.H)
13. Slide the door hang into door hang rails®. (fig.J – fig.K)
14. Take out the liners of the tapes on the front side of the door hang®.
15. Take out the liners of the tapes on the unit door spacers and and stick them onto the unit upper door®, closer to the upper corners. (fig.K)
16. Lean the unit door to the door hang, aligning the unit door spacers on the left, right and top edges with the sides of the unit or the doors of the nearer and upper kitchen units. (fig.K)
17. Make sure that the unit upper door sticks onto the door hang. Pull the unit door® allowing the door hang slide out the door hang rails. Observe that the door hang® stays sticked on the unit upper door®. (fig.L)
18. Lay down the unit upper door® to the floor and screw the door hang to the unit upper door® by screws. (fig.L)
19. To overcome some of the furniture mistakes, there are plastic spacers® sticked on the door hang. Remove these plastic spacers®. (fig.M)
20. Remove the door hang rails from the appliance upper door®. Screw the adjustment bolts to the holes on the appliance upper door® by leaving the necessary space using unit door spacer®. (fig.N)
21. Open the appliance upper door®. Place the unit upper door onto the appliance door inserting adjustment bolts® into the slots on the door hang®. (fig.N)
22. Place the washers and screw the nuts® onto the adjustment bolts. (fig.N) 23. 1~2 mm gap between the unit itself and unit door is vital for appliance performance. Close the door and make the accurate adjustment of the unit door by screwing or unscrewing the adjustment bolts® for vertical adjustment and by the help of the slots on the door hang® for other directions. (fig.P1)
24. Place the door bottom fixings to the bottom of the appliance upper door® between the appliance upper door and unit upper door®. Screw the door bottom fixings to the appliance door with screws®. (fig.O)
25. Screw the door bottom fixings to the unit upper door® by screws. (fig.O)
26. For the adjustment of the space between the unit upper door and the unit itself, you can unscrew the screws® then adjust the space between the appliance upper door and unit upper door® by the spring effect of the door bottom fixings while screwing back the screws.
27. Slide the hang cover onto the door hang®. (fig.P2)
28. Repeat the same procedure for the lower door.