This article explains how to assemble the BRV102 by Boretti.
INSTALLATION
Location
The appliance should be installed well away from sources of heat such as radiators, boilers, direct sunlight etc. For the encasement refer to the instructions provided. Electrical connection Before plugging in, ensure that the voltage and frequency shown on the serial number plate correspond to your domestic power supply. Voltage can vary by ±6% of the rated voltage. For operation with different voltages, a suitably sized auto-transformer must be used. The appliance must be earthed. The power supply cable plug is provided with a contact for this purpose. If the domestic power supply socket is not earthed, connect the appliance to a separate earth in compliance with current regulations, consulting a specialist technician. Door reversibility The appliance is supplied with the door opening to the right. For door opening in the opposite direction, perform the following actions prior to installation ! Warning! When changing the side at which the door opens, the appliance may not be connected to the mains. Remove plug from the mains beforehand.
2. Remove the door.
3. Unscrew with a key the lower pin and replace it on the opposite side.
4. Reinsert the door, refit the spacer and rescrew the upper pin on the opposite side. Instructions for totally built-in appliances Building-in instructions Dimensions of housing Height 1030 mm Depth 550 mm Width 560 mm For safety reasons, minimum ventilation must be as shown in Fig.
⚠ Attention: keep ventilation openings clear of obstruction. D567 50 mm min. 200 cm² min. 200 cm² Instructions pour l'encastrement Dimensions de la niche Hauteur (1) 1030 mm Profondeur (2) 550 mm Largeur (3) 560 mm La porte de l'appareil a éte immobilisée pour le transport au moyen de pivots. Enlevez le pivot superieur et inferieur conformement au sens d'ouverture de la porte. Pour des raisons de sécurité, la ventilation doit être prévue comme indiqué dans le Fig. Attention: veillez à ne pas obstruer les ouvertures de ventilation. Il est également nécessaire que la niche soit équipée d'un conduit d'areation ayant les mesures suivantes: Profondeur Largeur 50 mm 540 mm D567 PRO 50 mm min. 200 cm²
-540- 50 3 2 1 Veillez à maintenir une distance de 44 mm dans le bas de l'appareil entre le bord de l'appareil et la paroi du meuble. Le cache charnière inférieur qui se trouve dans le sac d'accessoires sert à garantir la position exacte du meuble et de l'appareil. Veillez également à ce que l'appareil n'écrase pas le câble d'alimentation. 44mm Fixez l'appareil à l'aide des 4 vis livrées à cet effet. Appliquez le joint à pression, entre l'appareil et le meuble. D724 1 min. (200 cm² Apply covers (C-D) on joint cover lugs and into hinge holes. Snap vent grille (B) and hinge covers (E) into position. Separate parts Ha, Hb, Hc, Hd as shown in the figure. Place guide (Ha) on the inside part of the furniture door, up and down as shown in the figure and mark the position of external holes. After having drilled holes, fix the guide with the screws supplied. Fix cover (Hc) on guide (Ha) until it clips into place. Open the appliance door and the furniture door at 90°. Insert the small square (Hb) into guide (Ha). Put together the appliance door and the furniture door and mark the holes as indicated in the figure. Remove the brackets and mark a distance of 8 mm from the outer edge of the door where the nail must be fitted (K). Place the small square on the guide again and fix it with the screws supplied. Should the lining up of the furniture door be necessary, use the clearance of slots. At the end of operations, it is necessary to check if the door of the furniture closes properly. Fix cover (Hd) on guide (Hb) until it clips into place. Inner door reversal Apply covers (C-D) on joint cover lugs and into hinge holes. Snap vent grille (B) and hinge covers (E) into position. Separate parts Ha, Hb, Hc, Hd as shown in the figure. Place guide (Ha) on the inside part of the furniture door, up and down as shown in the figure and mark the position of external holes. After having drilled holes, fix the guide with the screws supplied. Fix cover (Hc) on guide (Ha) until it clips into place. Open the appliance door and the furniture door at 90°. Insert the small square (Hb) into guide (Ha). Put together the appliance door and the furniture door and mark the holes as indicated in the figure. Remove the brackets and mark a distance of 8 mm from the outer edge of the door where the nail must be fitted (K). Place the small square on the guide again and fix it with the screws supplied. Should the lining up of the furniture door be necessary, use the clearance of slots. At the end of operations, it is necessary to check if the door of the furniture closes properly. Fix cover (Hd) on guide (Hb) until it clips into place. Inner door reversal Apply covers (C-D) on joint cover lugs and into hinge holes. Snap vent grille (B) and hinge covers (E) into position. Separate parts Ha, Hb, Hc, Hd as shown in the figure. Place guide (Ha) on the inside part of the furniture door, up and down as shown in the figure and mark the position of external holes. After having drilled holes, fix the guide with the screws supplied. Fix cover (Hc) on guide (Ha) until it clips into place. Open the appliance door and the furniture door at 90°. Insert the small square (Hb) into guide (Ha). Put together the appliance door and the furniture door and mark the holes as indicated in the figure. Remove the brackets and mark a distance of 8 mm from the outer edge of the door where the nail must be fitted (K). Place the small square on the guide again and fix it with the screws supplied. Should the lining up of the furniture door be necessary, use the clearance of slots. At the end of operations, it is necessary to check if the door of the furniture closes properly. Fix cover (Hd) on guide (Hb) until it clips into place. Inner door reversal