This article explains how to assemble the MLWC82 by Boretti.
Before connecting the wine cabinet to the power source, let it stand upright for at least 6 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation. Clean the interior surface with lukewarm water using a soft cloth. Read the instructions supplied with the appliance – failure to install or use of the appliance in accordance with the instructions may invalidate any warranty. Boretti does not accept any liability for damage caused through improper use, or incorrect installation. Do not install this appliance if it has been damaged during transportation. This includes the plug and supply cord. Please keep these instructions in a safe place for future reference.
Installation of the wine cabinet
1. Place you wine cabinet on a flat floor that is strong enough to support it when it is fully loaded.
2. This appliance uses flammable refrigerant. Never damage the cooling pipework during transportation and installation.
3. Locate the wine cabinet away from direct sunlight and sources of heat (stove, heater, radiator, etc.). Direct sunlight may affect the acrylic coating and heat sources may increase electrical consumption. Extreme cold ambient temperatures may also cause the unit not to perform properly.
4. Avoid locating the unit in moist areas.
5. Put the plug of the wine cabinet into an appropriate socket. Should the plug require changing, get help from a qualifed service technician.
6. Ensure the product is correctly ventilated (See section 1.3).
7. Plug the wine cabinet into an exclusive, properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) pin from the plug. Any questions concerning power and/or grounding should be directed toward a certified electrician or Customer Service Boretti.
Ventilation
The MLWC82 is already equipped with a vent slot on the front side. This model is also recessed to fit a kitchen plinth. If fitting a kitchen plinth is desired, please remove the air grid by removing both screws in front. A 55mm high vent slot is required in the plinth to ensure air is able to ventilate properly. See the diagram below. Failure to include this vent slot will invalidate the guarantee. Please note that the appliance doesn't come with a grille which slots-onto the kitchen plinth.
Appliance dimensions
How to change the door opening
This appliance has reversible doors but is delivered with a right hand hinged door. Should wish to reverse the hinge on your unit, follow the directions below:
1.Decorative screws 2. Door 2
3.Door Hinge
4.Screws
1. Open the door and remove the decorative covers (1) on the left hand side as shown in Fig. A.
2. Fix the screws into these positions a per Fig.B, but do not fasten the screws.
3. Remove all screws from both the upper and lower hinge, and then remove the door.
4. Rotate the door 180 degrees, and place the hinges into the screws fixed in Fig.B. Once slotted onto these screws, tighten the screws to secure the hinges (Fig D).
5. Placed the decorative covers in the right hand side and screw holes as shown in Fig.D
Installing the appliance
Place you wine cabinet on a floor that is strong enough to support it when it is fully loaded. The kitchen unit must be aligned horizontally and vertically. You will need to install a furniture door frame to the front of the wine cabinet once wine cabinet has been installed. The furniture door frame can be custom made (by the kitchen reseller) to line up with your other furniture doors in the kitchen. The door must be finished on both sides in order to prevent warping. Note: The door panel must not weight more than 10kg. Note: We recommend the door thickness does not exceed 18mm. If a thicker door is used, the door may make contact with the adjacent furniture door when opened. Steps
1. If you want to adjust the height over 820mm, please install the product using the foot sliders provided. These are provided to help prevent the feet catching on the floor when sliding the appliance into the aperture. BACK FRONT
2. To level you wine cabinet, adjust the front and back by leveling adjustable legs at the bottom of the cabinet (to 4mm less than the recess or handlebar height). Ensure it's perfectly leveled, as this will minimize any vibrations and noises.
3. Slide in the appliance until the front surface of the appliance door is behind the cabinet fronts. Place the furniture door frame on the cabinet to determine the right installation depth. Please make sure when sliding in the appliance, that the power supply cord is not damaged.
4. The included bracket will keep the product secure and help prevent it moving when in use. Line the fixing bracket with the two holes at the top of the wine cabinet. Use the screws to secure into position. Use the screws to secure the bracket to the side of the kitchen cabinet.
5. Installing the furniture door
If a handle is required, please ensure this is installed in an appropriate position before the furniture door is installed on the cabinet door. i. Fully open door. ii. Starting at the corner, pull the gasket away from the door. Continue to pull the gasket free from the gasket channel. iii. Upon removal, lay gasket down on a flat surface. iv. Align the furniture door panel with the cabinet doors. Secure the furniture door to the appliance door using clamps. v. Using a 3 mm drill bit, drill 6 pilot holes into the wood panel 12 mm deep using the holes in the door frame as a guide. Note: It is important to ensure that all drilled holes are drilled to the correct depth in order to avoid splits in the wood when hardwood is installed. You must also take care not to drill all the way through the door. vi. Locate 6 of the M4x34 mm screws provided with your unit. vii. Use a screwdriver, place one screw into each of the 6 pilot holes and screw into the door, Be careful not to over tighten screws. Ensure the screws sit flush against the bottom of the channel. Remove clamps from door. Note: If panel requires additional adjustment after removing clamps, slightly loosen each screw and adjust panel as necessary. Tighten screws upon completion. viii. Starting at the corners, re-install the gasket into the gasket channel in the frame, by pushing firmly into place. Make sure the gasket is fully seated into the channel.
Example inframe style door
This is an example of a X13 Raster size handleless kitchen cabinet door. The height of the furniture door will need to be adjusted to ensure it lines up with the other kitchen cabinet doors, therefore these dimensions will vary. The minimum overall height of the furniture door must be at least 715mm. Note: The furniture door can extend beyond the appliance door, however you must ensure a gap of at least 75mm is left between the bottom of the furniture door and the floor to allow for sufficient ventilation.
Permitted room temperature
The permitted room temperature depends on the appliance's climate class. The climate class can be found on the rating plate. Climate Class Permitted room temperature SN 10°C - 32°C 16°C - 32°C ST 16°C - 38°C 16°C - 43°C SN-ST 10°C - 38°C SN-T 10°C - 43°C The appliance is fully functional within the permitted room temperature. If an appliance with climate class SN is operated at colder room temperatures, the appliance will not be damaged up to a room temperature of 5 °C.