This article explains how to assemble the MLWC60AN / MLWC88AN / MLWC60ZW / MLWC88ZW by Boretti.
Before connecting the wine cabinet to the power source, let it stand upright for at least 6 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation. Clean the interior surface with lukewarm water using a soft cloth. Read the instructions supplied with the appliance – failure to install or use of the appliance in accordance with the instructions may invalidate any warranty. Boretti does not accept any liability for damage caused through improper use, or incorrect installation. Do not install this appliance if it has been damaged during transportation. This includes the plug and supply cord. Please keep these instructions in a safe place for future reference.
2. This appliance uses flammable refrigerant. Never damage the cooling pipework during transportation and installation.
3. Place your wine cooler on a cabinet shelf that is strong enough to support it when it is fully loaded.
4. Avoid locating the unit in moist areas.
5. Put the plug of the wine cabinet into an appropriate socket. Should the plug require changing, get help from a qualifed service technician.
6. Ensure the product is correctly ventilated (See section 1.5).
7. Plug the wine cabinet into an exclusive, properly installed-grounded wall outlet. Do not under any circumstances cut or remove the third (ground) pin from the plug. Any questions concerning power and/or grounding should be directed toward a certified electrician or Customer Service Boretti. This appliance has reversible doors but is delivered with left opening door. please follow the instructions below for changing the door to the right opening.
1. Top hinge 2.Door light switch
3.Location-plate 4. Bottom hinge
5. Support
- Place the cabinet on a soft surface and put the front on a mat height around 200mm to support the cabinet. This is used to prevent damaging the door, because the door is bigger than the cabinet
- (Fig.A); Open the door in a 90° angle. Remove 4 screws and top hinge (1) at the right top of the cabinet. Remove the door from the cabinet and put the door in place where it can't be damaged
- (Fig.B); Remove the door light switch (2) with 2 screws from the bottom of the door. Then reinstall the door light switch (2) with 2 screws in the opposite direction; top central of the door.
- (Fig.B); Remove the location-plate (3) with screws from the right bottom of the door. Then reinstall the location-plate with screw to the diagonal direction (left top of the door)
- (Fig.C, D); Incline the wine cooler with 45 degrees. Remove the screws and the bottom hinge (4) in the right bottom of the cabinet. Remove the screws and supporter (5) at the left bottom of the cabinet. Then install the supporter (4) to the right bottom of the cabinet.
- (Fig.D) Install bottom hinge (4) to the bottom left of the door.
- (Fig.E) Rotate the door at 180°.
- (Fig.F);Install the top hinge (1) with screws to the left top of cabinet, align the door with cabinet Place you wine cabinet on a cabinet shelf that is strong enough to support it when it is fully loaded. The kitchen unit must be aligned horizontally and vertically. Make sure that the cabinet is correctly ventilated according ventilation slots below. MLWC60AN / MLWC60ZW Length of power cord: 200cm Maximum door opening angle: 100° MLWC88AN / MLWC88ZW Length of power cord: 200cm Maximum door opening angle: 100° After the wine cooler is placed into kitchen cabinet, adjust the top bracket (A) close to the front of the kitchen cabinet (B). Fix the 3x screws through the top bracket (A) into kitchen cabinet (B). A. Top Bracket B. Kitchen Cabinet C. Screws D. Screwdriver E. Wine cooler Fix the 3x screws through the bottom bracket (D) into kitchen cabinet (B). A. Wine cooler B. Kitchen Cabinet C. Screws D. Bottom bracket The permitted room temperature depends on the appliance's climate class. The climate class can be found on the rating plate on the side of the cabinet. Climate Class Permitted room temperature SN 10°C - 32°C 16°C - 32°C ST 16°C - 38°C 16°C - 43°C SN-ST 10°C - 38°C SN-T 10°C - 43°C The appliance is fully functional within the permitted room temperature. If an appliance with climate class SN is operated at colder room temperatures, the appliance will not be damaged up to a room temperature of 5 °C.