This article contains the manual for the COMBIMAGNETRON BPC-45 by Boretti.
Dear Customer, We would like to thank you and congratulate you on your choice. This new product has been carefully designed and built using top quality materials, and meticulously tested to ensure that it meets all your culinary requirements. Please read and observe these simple instructions, which will enable you to achieve excellent results from the very first time you use it. IMPORTANT INSTRUCTIONS AND SAFETY
WARNINGS
READ CAREFULLY AND KEEP
FOR FUTURE USE
IMPORTANT
The combimagnetron’s identification plate is even accessible when the appliance is installed. This identification plate, which is visible when you open the door, shows all the information you will need when requesting replacement parts for the appliance. FIRST USE The combimagnetron should be thoroughly cleaned with soap and water and carefully rinsed. Heat the combimagnetron for about 30 minutes at the maximum temperature; this eliminates all the residual manufacturing oils that could cause unpleasant odours during cooking. Use the circular plus fan function without accessories in the combimagnetron. Before using the accessories for the first time, clean them carefully with a very hot alkaline washing solution and a soft cloth. IMPORTANT: As a safety precaution, before cleaning the combimagnetron, always disconnect the plug from the outlet or remove the appliance’s power cord. In addition, avoid using acid or alkaline substances such as lemon, vinegar, salt, tomatoes, etc.). Avoid using products containing chlorine, acids or abrasives, especially for cleaning the painted walls. RESPECT FOR THE ENVIRONMENT The documentation for this appliance is printed on paper bleached without chlorine or recycled paper to contribute to protecting the environment. The packaging was designed to prevent damage to the environment; they are ecological products that can be recovered or recycled. Recycling the packing saves raw materials and reduces the volume of industrial and domestic waste. THE PACKING MATERIAL is 100% recyclable and marked with the recycling symbol. Dispose of in conformity with local law. The packing material (plastic bags, polystyrene parts, etc.) must be kept out of the reach of children because it is potentially dangerous. THIS APPLIANCE is marked in conformity with European Directive 2002/96/EC, Waste Electrical and Electronic Equipment (WEEE). By making sure that this product is disposed of correctly, the user contributes to preventing potential negative consequences for the environment and health. THE SYMBOL on the product or accompanying documentation indicates that this product must not be treated as domestic waste but must be delivered to a suitable collection point for the recycling of electrical and electronic equipment. DISPOSAL MUST BE MADE in conformity with local laws on waste disposal. FOR ADDITIONAL INFORMATION about the treatment, recovery and recycling of this product, contact the local office of competence, the domestic waste collection service or the store where the product was purchased. BEFORE SCRAPPING, make it unusable by cutting the electrical cord. INTRODUCTION TO THE Combimagnetron Dear Customer, your new combimagnetron is controlled by an electronic board that constantly monitors its operation to improve its performance. The touch controls are state-of-the-art, precise and reliable. The interface is elegant, orderly and discrete, more intuitive than ever! A few buttons, many functions and no combination or sequence is difficult to enter, so you can concentrate on following the recipe and the combimagnetron is ready in two clicks! Installation and hook-up Dear Customer, this combimagnetron is a sophisticated electronic appliance, classified as a durable good. Its installation requires qualified professionals for both the hook-up of the power line and itsplacement in the kitchen counter. (SEE ASSEMBLY INSTRUCTIONS ON PAGE 56) Before hook-up When the combimagnetron is connected to the electric mains for the first time, the display will ask you to select your language; use the buttons to select the language you want; use the button to confirm the choice; ((from now on, the language choice will remain fixed even when their are power outages). Now, it goes into demonstration mode Demonstration mode This is the mode that the combimagnetron is normally in every time that there is a power failure and, consequently, when it is first hooked-up: the purpose is to show how you can control it with a recorded sequence of commands. In this mode, the combimagnetron is never REALLY turned on, i.e., the heating elements are never powered! The control panel is INACTIVE and, so, the combimagnetron will not respond to commands! To disable the demonstration mode, touch the light symbol for five seconds: the control will go to normal operation and ready for turning on. Now you can set the time but it is not necessary for turning on the combimagnetron.