This article explains how to use the BPWKN 45 by Boretti.
Accessory Installation Before Operating
Unpacking and Cleaning the Wine Cooler
Remove the exterior and interior packing materials. Let the appliance stand upright for approximately 2 hours before connecting it to the power source, which helps to reduce the possibility of a cooling-system malfunction from handling during transportation. Use a soft cloth to clean the interior surface with lukewarm water. Operating the Wine Cooler Working Climate The appliance is designed for operating from SN to T climate (see below climate class chart). It is recommended to maintain the ambient around 22-25°C which helps the appliance working with low power consumption. Climate Class Ambient Temperature SN 10 - 32 °C (50 °F – 90 °F) 16-32 °C (61 °F – 90 °F) ST 18 - 38 °C (64 °F – 100 °F) 18 - 43 °C (64 °F – 109 °F) If the ambient temperature is above or below the designed climate range, the performance of the unit may be affected. For example, the appliance operating in extreme cold or hot conditions may cause interior temperatures to fluctuate, and the temperature set 5-22°C may not be reached sometimes. Wine Storage The standard shelves are designed perfectly for Bordeaux bottle storage. The maximum loaded bottles may vary subject to the different size or dimension wine bottles you store. The shelves are with Telescopic Rails which has stoppers by themselves. To prevent damaging the door gasket, make sure to have the door opened fully all the way before pulling the shelves out. Please store wine in sealed bottles. Do not cover the shelves with aluminum foil or any other shelf material which may prevent air circulation. Should the wine cooler be left empty for long periods it is suggested that the appliance is unplugged, and after careful cleaning, leave the door ajar to allow air to circulate inside the cabinet in order to avoid possible condensation, mold or odours forming. Recommended temperatures for chilling/storing your wines. Red Wines 15-18 °C (59 °F – 64 °F) Dry/White Wines 9-14 °C (48 °F – 57 °F) Rose Wines 10-11 °C (50 °F – 52 °F) Sparkling Wines 5-8 °C (41 °F – 46 °F) Control Panel For Single Zone Power Lighting Temp.Up Display Window Temp.Down Lock/Unlock °C/°F Interchange Fig. 3 Power On/Off Control When the appliance is plugged in to a power outlet, it powers on automatically. Touch the power mark and hold for 10 seconds to turn off (or turn on) the appliance. No matter it is under a locked or unlocked situation, you can turn off the appliance by touching the power mark and holding for 10 seconds.
⚠ Warning: To avoid breaking the compressor, please do not turn on the appliance again within 5 minutes after you turn it off. Unlocking the Control Panel To unlock the control panel, touch the power mark and lighting mark with 2 fingers at the same time and hold for 3 seconds. When unlocked a buzz sound will be heard. The control panel will be automatically locked with a buzz sound heard after 10 seconds without being touched. Under the locked situation, the control panel will not react to any touching (except the power mark which works as above Power On/Off Control description). Interior Lighting On/Off Control Under the unlocked situation, touch the lighting markto turn on (or turn off) the interior cool LED lighting. The lighting will be continuously on if it is not turned off. The control panel will be automatically locked with a buzz sound heard after 10 seconds without being touched. Under the locked situation, the control panel will not react to any touching (except the power mark which works as above Power On/Off Control description). Touch the power mark and lighting mark with 2 fingers at the same time and hold for 3 seconds to unlock the control panel. When unlocked a buzz sound will be heard. Temperature Display Window The temperature is displayed in digital which is the best way to be read out. The digital is shown as the set temperature when you are setting the temperature, and it will change to be the real temperature of the inside cabinet after 10 seconds without being touched. When the temperature probe is out of order, the display window will show with “HH” or “LL” instead of a digital figure while continuous buzz sound will be heard. In case of this happens, this appliance is considerately designed to keep periodical running of compressor and fans which helps to keep the coldness of the inside cabinet to protect your stored wines. Warning: To avoid destroying your stored wines, it is strongly recommended to have the appliance repaired immediately, as the spare periodical running can not ensure the appliance to achieve the temperature you have set. Temperature Setting For Single Zone The temperature setting range is 5-22 °C (41-72 °F). Directly touch the or mark to set the wine cooler temperature as you want. The first touch on + or mark will recall the previous set temperature displayed in the digital window. If the appliance runs after a power failure (or unplugging), the previous set temperature does not exist and is replaced by the defaulted temperature at 12°C. Touch the mark + to increase the set temperature by 1°C. On the contrary, touch the mark to decrease the set temperature by 1°C. The digital will change to display the real temperature of the inside cabinet after 10 seconds without being touched. Note: For the first time to use the appliance or to restart the appliance after having been shut off for a long time, you may find a few degrees variance between the set temperature and the displayed temperature. It is normal and everything of the appliance will be in the order after a few hours running Selecting Fahrenheit(°F) & Celsius (°C) Display For Single Zone Touch the marks °C/°F- with 2 fingers at the same time and hold for 5 seconds, you can interchange the Fahrenheit and Celsius display. For Dual Zone °C °F Directly touch the mark you can interchange the Fahrenheit and Celsius display for both zones at the same time.