This article explains how to use the BCHSB-60 + 90 + 120 by Boretti.
CONTROLS
A) Turns the LIGHTS off
B) Turns the LIGHTS on. C) Decreases speed down to minimum speed. If pressed for 2" the motor is turned off. D) Activates the motor (calling the last speed used) and increases the speed until reaching maximum. E) FILTER ALARM/TIMER RESET: when pressing the key during display of the filter alarm (motor off) it resets the hour counter. When pressing the key when the motor is running, the TIMER is activated and the hood will automatically be switched off after 5 minutes. L1) The 4 green LEDs indicate the running speed. L2) When the LED is red (motor off) it indicates the FILTER ALARM. When the LED is green (flashing) it indicates that the TIMER has been activated with the key E. FILTER ALARM: After 30h of operation, the LED L2 turns RED. It indicates that the grease filters need to be cleaned. After 120h of operation, the LED L2 turns RED and flashes; It indicates that the grease filters need to be cleaned and the charcoal filters replaced. After cleaning the grease filters (and/or replacing the charcoal filters), restart the hour counter (RESET) by pressing the key E during display of the filter alarm. OFF ON OFF/- ON/+ L1 E L2 CONTROLS P1) Lights OFF: If pressed, lights go off. P2) Lights ON: If pressed, lights go on. P3) OFF/- Motor: Speed drop until minimum speed is reached. If pressed for 2", motor switches off. If pressed for 2" with FILTER RESET on HOUR count reset. P4) ON/+ Motor: Starts motor and increases motor speed until top speed is reached P5) ON/OFF: Switches Sensor off and on(AUTOMATIC or MANUAL mode). In Automatic mode, LED L2 is on and L1 shows operating speed In Manual mode, LED L2 is off. L1) 4 LEDs 4 GREEN LEDs. Indicate set speed L2) 4 LEDS GREEN indicates AUTOMATIC mode OFF indicates MANUAL mode RED indicates Filter Reset FILTER RESET: shown with Motor Off for 30": After 30h the LED L2 becomes steady RED. After 120h LED L2 becomes flashing RED Reset by means of P3 SENSITIVITY: In manual mode, by pressing P5 and P4 together, sensitivity mode is entered. The set sensitivity is indicated by the 4 green LEDs. By means of buttons P3(-) and P4(+) the desired sensitivity is set. By pressing P5 the sensitivity can be stored, with return to manual mode. OFF ON ON/OFF OFF/- ON/+
* L1 P1 P2 P3 P4 P5 L2 CONTROLS Key A: light switch. Key B: first speed motor ON/OFF switch. Key C: second speed switch. Key D: third speed switch. CONTROLS ㅇㅇㅇㅇ Button A: light button. Button B: first speed motor ON/OFF button. Button C: second speed motor ON/OFF button. Button D: third speed motor ON/OFF button. E: motor on light. CONTROLS Key A: light switch; position 0: light off; position 1: light on. Key B: motor switch; position 0: motor off; position 1-2-3: motor first, second and thrid speed motor on. 01 CONTROLS Key A = turns the lights on/off. Key B = turns the TIMER on/off: press once to turn the timer on, therefore, after 5 minutes, the motor cuts out (at the same time the selected speed blinks on the display); the timer remains on if the motor speed is changed. Display C = indicates the selected motor speed (from 1 to 4); indicates Timer On when the number blinks; indicates Filter Alarm when the central segments is on or blinking. Key D = makes the motor work (at the last speed selected); pushing the button again, the speeds of the motor are sequentially selected from 1 to 4; keeping this button pressed for about 2 seconds shuts down the motor. Key R = resets the grease filters or charcoal filters; when the filter alarm appears (i.e. when the central segment on the display goes on), the grease filters must be cleaned (30 hours of operation); when the central segment starts blinking, the grease filters must be cleaned and the charcoal filters replaced (120 hours of operation). Obviously, if the hood is not a filtering model and does not have a charcoal filter, clean the grease filters both when the central segment goes on and when it starts blinking. The filter alarm can be seen when the motor is off and for about 30 seconds. To reset the hour counter, keep the button pressed for 2 seconds while the alarm zero (stopping). Whenever the key is pressing during filter alarm display, a RESET occurs, and the counting of the hours resumes again. Key E: enables the motor / increases motor speed /TIMER. Pressing this key starts the motor (at the latest speed set); pressing the key again increases motor speed, while keeping the key pressed down for a few se- conds enables the TIMER, and 5 minutes later the motor will stop (while the number of speed setting selected will simultaneously begin flashing on the display); the Timer will remain enabled if motor speed is changed. In order to disable the Timer, press the key again. 808 SENSOR ON/- ON/+ OPERATION INSTRUCTIONS SETTING THE CLOCK (to be done with the hood in stand-by) 1) press and hold Button 1 until the hour digits begin to flash 2) change the hour by pressing Button 2 (-) or Button 3 (+) 3) Once the hour is set, press Button 1. The minute digits will flash 4) change the minutes by pressing Button 2 (-) or Button 3 (+) 5) press Button 1 to return to normal view. The time has now been set TURNING THE LAMPS ON AND OFF (place alongside the lamp picto- gram) Press Button 2 to turn the lights on/off. If the lights are on this is also indica ted by the lighting of the luminous ring around Button 2 and the lighting of the "Lamp" icon on the display TURNING ON THE HOOD MOTOR (place alongside the + pictogram) Press Button 4 to turn on the motor which will start at speed 3 for 2 secon- ds. Then the hood will set the most recent speed set before the last shut down. Or: Press Button 3 to turn on the motor which will start at speed 3 for 2 secon- ds. Then the hood will set the most recent speed set before the last shut down. If the hood is on this is indicated by the lighting of the luminous ring around Buttons 3 and 4 and the lighting of the "Speed" icon on the display VARIATION OF THE MOTOR SPEED (place alongside pictogram +) Press Button 3 repeatedly to change the motor speed sequentially, from slowest to fastest. The motor speed icon turns at a speed proportional to the speed selected (slower for the first speed, faster for the second and still faster for the third) ACTIVATION OF THE TIMER FEATU gram) The timer feature allows the hood to operate for a defined period of time. When the time expires the hood shuts off. with the motor on: press Button 1 to activate the Timer feature. When the timer feature is active the "timer" icon will appear on the display, the luminous ring around Button 1 flashes and the display shows the duration of the countdown. timer is set automatically to 5 minutes, but pushing Button 2 or Button 3 increases/decreases the duration of the countdown Once the duration of the timer is set, the countdown can be started by pressing Button 1 (if Button 1 is not pressed within 10" the countdown will start automatically) To interrupt the timer and deactivate the feature press Button 1 during the countdown. Upon expiry of the countdown the hood will emit a double beep and the motor will shut off TURNING THE HOOD OFF (place alongside the Press Button 4 NOTE: With the hood in stand-by (lights off, motor off, display off), press any button to turn on the display back-light without activating any functions. Only by pressing buttons P2, P3, P4 can their relative functions be activated. If no other button is pressed within 15 seconds of pressing the first button, the display turns off and the hood returns to the stand-by mode. (+)
* 0/1 CONTROLS PU4: ON/OFF Motor 3rd speed PU3: ON/OFF Motor 2nd speed PU2: ON/OFF Motor 1st speed PU1: ON/OFF Lights 5' timer function: Pressing PU2, PU3 or PU4 for two seconds when the motor is set to the corresponding speed, the 5' timer function is activated. The corresponding LED starts blinking to display this function. After five minutes of operation the motor is turned off. If you change the speed while the timer is running, the function is NOT deactivated. To deactivate the function, press the blinking key for two seconds. NOTE - the 5' timer function can be activated for the normal speeds only (1st, 2nd, 3rd) Filter alarm: After 30 hours of motor operation, the grease filter alarm is activated (all the LEDs come on). The alarm is activated when the motor is off and remains displayed for 30". To deactivate the alarm, press one of the keys for 2" during alarm display. After 120 hours of motor operation, the charcoal filter alarm is activated (all the LEDs blink). The alarm is activated when the motor is off and remains displayed for 30". To deactivate the alarm, press one of the keys for 2" during alarm display. P1: 5' TIMER P2: Filter alarm reset P3: Motor off / speed decrease -
- holding down the button, the motor turns off sto- ring the current speed P4: Motor on / speed increase P5: Lights on/off L1 Signalling crown: Motor on: L1 lights up turquoise flashing. The flashing frequency is proportional to the speed 5' TIM ER function: L1 lights up turquoise fixed Filter alarm active: L1 lights up red fixed (30h); L2 lights up red flashing (120h) P1 P3 P5 P4 P2 L1 Button TC1 (Lights) Switches main light ON/OFF When the main light is on, BL1 changes colour and becomes active. When the button is pressed for more than a second, it switches the courtesy lights (optional) on/off Button TC2 (Motor-V1) Motor ON/OFF - Activates the motor at 1st speed Button TC3 (Motor-V2) Activates the motor at 2nd speed Button TC4 (Motor-V3) Activates the motor at 3rd speed Button TC5 (Motor-V4) Activates the motor at 4th speed Maximum speed is timed at a maximum of 5 minutes, after which 3rd speed is set automatically. When the motor is active, the LED of the last selected button (TC2-TC5) active to signal which speed has been set. Button TC6 (TIMER auto power off 5 min.) Activates the TIMER function at the speed that has already been selected If the motor is NOT active, it switches on the motor at the 1st speed and activates the TIMER function When the TIMER function is active, BL6 becomes active. 30h filter ALARM After 30 hours of operation, an alarm switches on to signal the need for anti-grease filter cleaning. The filter alarm, when active, is displayed for 30 sec each time the motor is deactiva- ted: BL6 remains ON. During this period, it is possible to reset the alarm by pressing the TC6 button for longer than a second. 120h filter ALARM After 120 hours of operation, an alarm switches on to signal the need for active carbon filter (optional) replacement. The filter alarm, when active, is displayed for 30 sec each time the motor is deactiva- ted: BL6 lighting blinking. During this period, it is possible to reset the alarm by pressing the TC6 button for longer than a second Work Time Limit If the hood is left on (lights and/or motor), after 10 hours in the absence of commands from the user, it will automatically switch to OFF condition with all services switched off. Buzzer The Buzzer emits a "beep" each time that a command is set from the keyboard or remote control (optional) BL2 BL3 Button TC6 (Auto ASC) She activates/deactivates the automatic ASC function. Thus, the motor speed increases and decreases based on the quantity of smoke and odors produced under the hood. When the function is activated, BL6 lights up (continuous light). Each time the motor speed is changed, automatically or forced by the user, BL6 flashes for a few seconds. 30h filter ALARM. After 30 hours of operation, the grease filter cleaning alarm is activated. When the filter alarm is activated, it is displayed for 30 seconds each time the motor is switched off. BL6 remains ON. During this period, it is possible to reset the alarm by pressing the TC6 button for longer than a second. 120h filter ALARM. After 120 hours of operation, the active carbon filter replacement alarm is activated (optional). When the filter alarm is activated, it is displayed for 30 seconds each time the motor is switched off. BL6 starts blinking. During this period, it is possible to reset the alarm by pressing the TC6 button for longer than a second. Buttons TC5 + TC6 (ASC sensitivity) It is possible to modify the sensitivity of the odor sensor on 4 different levels, depending on your own needs. To do this, press and hold buttons TC5 and TC6 simultaneously. The motor must be switched off, and the automatic function CANNOT be active. When the function to set the sensitivity is activated: all BL lights go out (no display), then BL6 lights up with CONTINUOUS light. After 1 second, the LED lights BL2-BL5 show the selected sensitivity value, from BL2 for the lowest to BL5 for the highest sensitivity. It is possible to set another value, using the respective buttons TC2, TC3, TC4 or TC5. To save this new sensitivity, press button TC6 or wait until the function is automatically deactivated. It is possible to lock the keyboard (for cleaning purposes) by pressing and holding buttons TC1 and TC6 simultaneously. When the cleaning mode is activated, buttons TC1 and TC6 remain activated. To exit the cleaning mode, press TC1 and TC6 again simultaneously (long press) or wait 5 minutes. Work Time Limit If the hood remains on (lights and/or motor), after 10 hours in the absence of commands from the user, it will automatically switch to OFF condition with all services switched off. Buzzer Each time a command is given from the keyboard or remote control (optional), the Buzzer emits a "beep" sound. BL1 BL2 BL3 BL4 BL5 BL6 Toets L: lichtschakelaar. Toets 1: schakelaar ON/OFF motor op le snelheid. Toets 2: schakelaar ON/OFF motor op lle snelheid. Toets 3: schakelaar ON/OFF motor op Ill e snelheid. Toets 4: schakelaar ON/OFF motor op IV e snelheid. Alarm filters: na circa 30 uur werking, bij afgezette motor, knipperen de snelheidstoetsen (toetsen 1, 2, 3 en 4) gedurende 30 seconden om aan te geven dat de vetfilters gereinigd moeten worden. Druk, zodra de filters gereinigd zijn, 2 seconden op een van de toetsen tijdens het knipperen om de telling van de uren weer op te starten (Reset). Timer: de timer kan geactiveerd worden (vertraagde uitschakeling van 5 minuten) door 2 seconden op een snelheidstoets te drukken (toetsen 1, 2, 3 of 4) wanneer de motor werkt; de toets van de gekozen snelheid begint te knipperen. 來 01 2 3 04 1 2 3 4