This article contains the manual for the PRO 900 IX PRO 1000 IX PRO 1200 IX by Boretti.
ELECTRICAL CONNECTION. This cooker hood is fitted with a 3-core mains cable with a standard 10/16A earthed plug. Alternatively the hood can be connected to the mains supply via a double-pole switch having 3mm minimum contact gap on each pole. Before connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood. Technical Specification: Voltage 220-240, single phase ~50Hz / 220 V - 60 Hz. INSTALLATION ADVICE Ensure the cooker hood is fitted in compliance with the recommended fixing heights. To ensure the safe operation of this cooker hood, we recommend that the hood should not be fitted below 65cm (for electric) or (70cm for gas) the measurements taken from the surface of the cooking appliance to the underside of the cooker hood. It is a possible fire risk if the hood is not sited as recommended. To ensure the best results, the cooking fumes should be able to rise naturally towards the inlet grilles on the underside of the cooker hood and the cooker hood should be positioned away from doors and windows, which will create turbulence. Ducting If the room where the hood is to be used contains a fuel-burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type. If other types of flue or appliances are fitted ensure that there is an adequate supply of fresh air to the room. Ensure the kitchen is fitted with an airbrick, which should have a cross-sectional measurement equivalent to the diameter of the ducting being fitted, if not larger. The ducting system for this cooker hood must not be connected to any existing ventilation system, which is being used for any other purposes or to a mechanically controlled ventilation ducting. The ducting used must be made from fire retardant materials and the correct diameter must be used, as incorrect sized ducting will affect the performance of this cooker hood. When the cooker hood is used in conjunction with other appliances supplied with energy other than electricity, the negative pressure in the room must not exceed 0.04 mbar to prevent the fumes from combustion being drawn back into the room. The appliance is for domestic use only and should not be operated by children or people who are infirm without supervision. This appliance must be positioned so that the wall socket is accessible. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance. FITTING Any permanent electrical installation must comply with the latest regulations concerning this type of instal- lation and a qualified electrician must carry out the work. Non-compliance could cause serious accidents or injury and would deem the manufacturers guarantee null and void. IMPORTANT - The wires in this mains lead are coloured in accordance with the following code : green / yellow : earth blue: neutral brown: live As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows. The wire which is coloured green and yellow must be connected to the terminal in the plug which is marked with the letter E or by the earth symbol or coloured green or green and yellow. The wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black. The wire which is coloured brown must be connected to the terminal which is marked with the letter L or o loured red.
⚠ ATTENTION: Do not forget to use adequate plugs to the support brackets. Enquire after the manu- facturers. Do an embedding if necessary. The manufacturer accepts no responsibility in case of a faulty hanging due to the drilling and the setting up of plugs. 1) Draw a vertical line up the wall from the centre of the cooking appliance below as illustrated in fig. 4 - item 1. 2) Mark a point on the vertical line which corresponds to the lower canopy position (The height H of the splashback item B is 450 mm ) and draw a horizontal line parallel to the stove top at a distance of 580 - 18 mm above this point. 3) Mark the 2 hole centres for the canopy fixing cup screws item T at a distance both left and right of the vertical line of 312 mm as illustrated in fig. 4. 4) Place one of the brackets fig. 4, item 2 on the wall 2 mm from the ceiling or from the upper limited of the chimney aligning the notches on the bracket centrally over the vertical line and mark the hole centres 5) Place the second of the brackets item 2 on the wall aligning the notches on the bracket centrally over the vertical line, at a distance X, which is equivalent to the height of the upper chimney section item S, mark the hole centres and then drill the holes using an 8 mm masonry drill and fix the cup screws and the 2 brackets using the plastic rawl plugs provided. 6) Hook the canopy item C onto the cup screws item T as illustrated fig. 2. The canopy should be se- cured to the wall using the two key hole slots, whose centres are located 61 mm below cup screws. Unhook the canopy, drill the holes using a 6.5 mm masonry bit and insert the rawl plug. 7) Draw a horizontal line through the vertical level with the back edge of the cooking surface. Place the splashback against the wall onto the top of the cooking appliance. it could be fix by rawl plugs and screws on the bottom. 8) Hook the canopy item C onto the cup screws item T as illustrated in fig. 2. The canopy can be ad- justed horizontally and vertically ensuring the canopy aligns with the splashback and the cooking appliance, by turning the adjustment screw item V. The canopy can be adjusted so that it aligns with the wall by turning the adjustment screw item V2. 9) Secure the canopy to the wall using the security fixing screw as illustrated in fig. 3. 10) Place the noise-reduction tube item 4 over the round outlet on top of the canopy while pressing down until it snaps into position (Fig. 5), then the non-return backflow flaps item 3 over the noise-reduction tube and duct the canopy to the outside using ducting 150 mm (6 ins) manufactured from fire retard- ant material, produced to BS.476 or DIN 4102-B1. Before fitting the chimney to the canopy make the electrical connection as described in the section titled "ELECTRICAL WIRING", see as well UK specifications. When the electrical connection has been made, test the lights and the fan motor. Fit the silent pack item 5 as illustrated in fig. 6, operation 1 and 2 by clamping the two plastic rings on either side of the motor diffuser and fitting together noise-reduction casings and plastic rings. IN THE REMOTE INSTALLATION MODE : a. Connect the ducting 200 mm ( 8ins) onto the round outlets on the top of the canopy and onto the round inlet of the motors at a distance and secure the connections with appropriate clamping rings or adhesive tape. b. Connect the earth connection onto the terminal marked with the earth symbol and clamp the connector onto the motor housing as illustrated Fig. 12. 11) The chimney stack consists of two sections. Fit the upper section item S first by expanding the chimney slightly to allow it to clamp around the brackets item 2. Secure the chimney stack to the brackets using the four self tapping screws provided. Fit the lower chimney section item I by expanding the chimney slightly to allow it to clamp around the upper chimney section item S, and the bracket on top of the canopy item C as illustrated in fig. 5. Secure the chimney stack to the bracket using the two self tapping screws provided. 12) Place the 3 metal grease filters as illustrated in fig. 11. RECIRCULATION 1) Fit the recirculation spigot item R over the round outlet on top of the canopy while pressing down on the spigot until it snaps into position as illustrated in fig. 7. Note: The two recirculation ducts item G must be fitted onto the recirculation spigot R before fitting onto the canopy item C 2) Remove the metal grease filters and place one charcoal filter at a time over the grilles on either side of the motor housing and turn clockwise into position (A) as illsutrated in fig. 8. 3) Fit together noise-reduction casings and charcoal filters without the plastic rings on either side of the motor housing as illustrated in fig. 6, operation 2. OPERATION A - EXTRACTION OR RECYCLING Your cooker hood is supplied in the extraction mode. To use the cooker hood in the recirculation mode re-programme the hood as follows: Starting in the recirculation mode Press the '+' button for 10 seconds (while the motor and lights are switched 'OFF') and the two LED lights will flash twice to indicate confirmation that the cooker hood is in the recycling mode. Reverting to the extraction mode Press the '+' button for 10 seconds (while the motor and lights are switched 'OFF') and the two LED lights will flash once to indicate confirmation that the cooker hood is in the extraction mode. B-BASIC INSTRUCTIONS Lighting Press Button 1 to switch 'ON' the lights. Motor Press LED button 2 to switch 'ON' the fan motor, the LED F will illuminate to confirm the motor is swit- ched 'ON', and adjust the speed of the fan motor by pressing the Button '+' and '-'. The fan speed will be increased if constant pressure is kept on the (+) button. Press LED button 5 to obtain the boost position for maximum effect and the LED C will illuminate to confirm fan is switched 'ON'. C- COMPLEMENTARY INSTRUCTIONS Automatic pre-set stop for the boost speed after 10 mn. To obtain the best performance it is advisable to switch 'ON' the cooker hood a few minutes (in the boost setting) before you start cooking and you should leave it running for approximately 10 minutes after finishing. Press LED button 5 to switch 'OFF' the fan motor immediately. Indication of saturation of the metal grease filters After 100 hours use, one quick flash of the LED F will indicate that you must clean the metal grease filters. (See chapter on 'Maintenance'). This indication is not available when the fan motor is switched OFF. Indication of saturation of the active charcoal filter After 200 hours use, two quick flash of the LEDS F & C will indicate that you must replace the active charcoal filter and clean the metal grease filters. (See chapter on 'Maintenance'). To reset the 200-hour timer the motor and lights must be switched 'OFF'. Push the LED button '+' for 10 seconds. One flash of the LED lights F and C = function is switched 'OFF'. Two flashes of the LED lights F and C = function is switched 'ON'. To reset the 100 hours timer back to zero requires the motor and lights must be switched 'OFF'; then and proceed as follows: Press the LED button '+' for 3 to 4 seconds and the LED lights F and C will flash to confirm the programme has been reset to zero. Instructions for replacing the active charcoal filter are given in the chapter on 'Recycling'. Setup Process Modification: How to adjust the internal microprocessor data to suit the type of motor fitted to this appliance and the supply frequency of 50 or 60 Hz.. 1- Disconnect the cooker hood from the mains supply. 2- Push the button 0/1 MOTOR. 4- 3- Reconnect the mains supply while pushing the button 0/1 MOTOR for at least 2 seconds. Slacken the button 0/1 MOTOR (the Leds flash for about 3 seconds: capacity's confirmation SETUP PROCESS). 5- During the flashing time select the motor type used while pushing one of the 5 buttons according to the following board: BUTTON 0/1 Light : Motor FABER 8/28 & 8/50 220-240 V AC / 50 Hz. BUTTON 0/1 Motor : Motor FABER 8/28 & 8/50 220-240 V AC / 60 Hz. BUTTON Speed (-) : Motor EBM PRO 220-240 V AC / 50 Hz. BUTTON Speed (+) : Motor EBM PRO 220-240 V AC / 60 Hz. BUTTON Intensive speed : Motor K40 & K50 220-240 V AC / 50 Hz. REMOTE CONTROL HANDSET Caution, the remote control must be fitted with standard LR03-AAA size 1.5V zinc-carbon alkaline bat- teries as illustrated Fig. 9. These batteries should give a long life and constant discharge throughout their life. These batteries must be disposed of properly and could explode if damaged or exposed to heat. Do not dispose of on fire. USEFUL HINTS To obtain the best performance it is advisable to switch 'ON' the cooker hood a few minutes (in the boost setting) before you start cooking and you should leave it running for approximately 15 minutes after finishing. IMPORTANT: NEVER DO FLAMBÉ COOKING UNDER THIS COOKER HOOD Do not leave frying pans unattended during use as over-heated fat and oil might catch fire. Do not leave naked flames under this cooker hood. Switch 'OFF' the electric and gas before removing pots and pans. Ensure heating areas on your hotplate are covered with pots and pans when using the hotplate and cooker hood simultaneously. MAINTENANCE Before carrying out any maintenance or cleaning isolate the cooker hood from the mains supply. The cooker hood must be kept clean; a build up of fat or grease can be a fire hazard. Casing Wipe the cooker hood frequently with a clean cloth, which has been immersed in warm water contain- ing a mild detergent and wrung out. Never use excessive amounts of water when cleaning particularly around the control panel. Never use scouring pads or abrasive cleaners. Always wear protective gloves when cleaning the cooker hood. Metal Grease Filters The metal grease filters absorb grease and dust during cooking to help keep the cooker hood clean inside. The grease filters should be cleaned once a month or more frequently if the hood is used for more than 3 hours per day. To remove and replace the metal grease filters Remove the metal grease filters one at a time by releasing the catches on the filters; the filters can now be removed. The metal grease filters should be washed, by hand, in mild soapy water or in a dishwasher. Allow to dry before replacing. Active Charcoal Filter The charcoal filter cannot be cleaned. The filter should be replaced at least every three months or more frequently if the hood is used for more than three hours per day. To remove and replace the filter Remove the metal grease filters. Press against the two retaining clips, which hold the charcoal filter in place and this will allow the filter to drop down and be removed. Clean the surrounding area and metal grease filters as directed above. Insert the replacement filter and ensure the two retaining clips are correctly located. Replace the metal grease filters. Extraction tube. Check every 6 months that the dirty air is being extracted correctly. Comply with local rules and regula- tions with regard to the extraction of ventilated air. Lighting. If the lamp fails to function check to ensure it is fitted correctly into the holder. If lamp failure has occurred then it should be replaced with identical replacement. Do not replace with any other type of lamp and do not fit a lamp with a higher rating. GUARANTEE AND AFTER SALES SERVICE In the event of any malfunction or anomaly, notify your fitter who will have to check the ap- pliance and its connection. In the event of damage to the mains supply cable, this can only be replaced by at approved repair centre appointed by the manufacturer who have the necessary tools and equipment to carry out any repairs properly. Repairs carried out by other persons will invalidate the guarantee. Use only genuine spare parts. Should these warnings fail to be observed it could affect the safety of your cooker hood. When ordering spare parts quote the model number and serial number written on the rating plate, which is found on the casing behind the grease filters inside the hood. Proof of purchase will be required when requesting service. Therefore, please have your receipt available when requesting service as this constitutes the date from which your guarantee commenced. This Guarantee does not cover : Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or filters or removable parts of glass or plastic. These items are considered to be consumable under the terms of this guarantee. REMARKS This appliance complies with European regulations on low voltages Directive 2006/95/CE on electrical safety, and with the following European regulations: Directive 2004/108/CE on electromagnetic compat- ibility and Directive 93/68 on EC marking. When this crossed-out wheeled bin symbol is attached to a product it means the product is cov- ered by the European directive 2002/96/EC. Your product is designed and manufactured with high quality materials and components, which can be recycled and reused.Please inform yourself about the local separate collection system for electrical and electronic product. Please act according to your local rules and do not dispose of your old products with your normal household waste. The correct disposal of your old product will help prevent potential negative consequences for the environment and human health.