This article explains how to use the BI 60 / BI 60 MAT BI 80 / BI 80 MAT by Boretti.
Control panel
Timer display
Power display
Keep Warm Key
Control light on/off
÷88: Control light timer Control light cooking zone 8. 8. Control light Pause/Recall + PS Booster selection zone “SLIDER" and timer setting zone Booster Pause/Recall key key USE OF THE APPLIANCE Display Display 0 1...9 II Designation Zero Power level Pan detection Heat accelerator Error message Residual heat Booster Locking Keep warm Pause Function The heating zone is activated. Selection of the cooking level. No pan or inadequate pan. Automatic cooking. Electronic failure. The heating zone is hot. The boosted power is activated. Control panel locking. Maintain automatically of 70°C. The hob is in pause. Ventilation The cooling system is fully automatic. The cooling fan starts with a low speed when the calories brought out by the electronic system reach a certain level. The ventilation starts his high speed when the hob is intensively used. The cooling fan reduces his speed and stops automatically when the electronic circuit is cooled enough. STARTING-UP AND APPLIANCE MANAGEMENT Before the first use Clean your hob with a damp cloth, and then dry the surface thoroughly. Do not use detergent which risks causing blue-tinted colour on the glass surface. Induction principle An induction coil is located under each heating zone. When it is engaged, it produces a variable electromagnetic field which produces inductive currents in the ferromagnetic bottom plate of the pan. The result is a heating-up of the pan located on the heating zone. Of course the pan has to be adapted: • All ferromagnetic pans are recommended (please verify it thanks a little magnet): cast iron and steel pans, enamelled pans, stainless-steel pans with ferromagnetic bottoms... • Are excluded: cupper, pure stainless-steel, aluminium, glass, wood, ceramic, stoneware,... The induction heating zone adapts automatically the size of the pan. With a too small diameter the pan doesn't work. This diameter is varying in function of the heating zone diameter. If the pan is not adapted to the induction hob the display will show [ U ]. Sensitive touch Your ceramic hob is equipped with electronic controls with sensitive touch keys. When your finger presses the key, the corresponding command is activated. This activation is validated by a control light, a letter or a number in the display and/or a “beep” sound. In the case of a general use press only one key at the same time. Power selection zone “SLIDER” and timer setting zone To select the power with the slider, slide your finger on the “SLIDER” zone. You can already have a direct access if you put your finger directly on the chosen level. Power selection zone "SLIDER" and timer setting zone "SLIDER" Direct access Starting-up • Start up / switch off the hob: Action To start To stop Control panel press key [] press key [①] Display 4 x [0] are blinking nothing or [H] • Start up / switch off a heating zone: Action Zone selection To set (adjust the power) To stop Control panel press display [ 0 ] selected slide on the "SLIDER" to the right or to the left slide to [ 0 ] on “SLIDER“ or press on [0] Display [0] and control light on [0] to [9] [0] or [H] [0] or [H] If no action is made within 20 second the electronics returns in waiting position. Pan detection The pan detection ensures a perfect safety. The induction doesn't work: • If there is no pan on the heating zone or if this pan is not adapted to the induction. In this case it is impossible to increase the power and the display shows [ U ]. This symbol disappears when a pan is put on the heating zone. • If the pan is removed from the heating zone the operation is stopped. The display shows [ U ]. The symbol [ U ] disappears when the pan is put back to the heating zone. The cooking continues with the power level set before. After use, switch the heat element off: don't let the pan detection [U] active. Residual heat indication After the switch off of a heating zone or the complete stop of the hob, the heating zones are still hot and indicates [ H ] on the display. The symbol [ H ] disappears when the heating zones may be touched without danger. As far as the residual heat indicators are on light, don't touch the heating zones and don't put any heat sensitive object on them. There are risks of burn and fire. Booster function The booster function [ P ] grants a boost of power to the selected heating zone. If this function is activated the heating zones work during 5 minutes with an ultra high power. The booster is foreseen for example to heat up rapidly big quantities of water, like noodles cooking. • Start up / Stop the booster function: Action Zone selection Start up the booster Stop the booster Control panel press key [ 0 ] from the zone press key [P] slide on the "SLIDER" or press on [P] Display [0] and control light on [P] [P] to [0] [9] • Power management: The hole cooking hob is equipped by a maximum of power. When the booster function is activated, and not to exceed the maximum power, the electronic system orders to reduce automatically the power level of an other heating zone. The display is blinking on [ 9 ] during a few seconds and then shows the maximum of power allowed : Heating zone selected [P] is displayed The other heating zone: (example: power level 9) [ 9 ] goes to [ 6 ] or [ 8 ] depending the type of zone Timer The timer is able to be used simultaneous with all 4 heating zones and this with different time settings (from 0 to 99 minutes) for each heating zone. • Setting and modification of the cooking time: Example for 16 minutes at power 7: Action Control panel Display Zone selection press display [ 0 ] selected [0] and control light on Select the power level slide on the "SLIDER“ to [ 7] [7] Select << Timer >>> press display [ CL ] [00] Set the units slide on the "SLIDER“ to [ 6 ] [ 0 fixed ] [ 6 blinking ] Valid the units press display [ 06 ] [ 0 blinking ] [ 6 fixed ] Set the tens slide on the "SLIDER“ to [ 1] [ 1 blinking ] [ 6 fixed ] Valid the tens press display [ 16 ] [ 16 ] The time is confirmed and the cooking starts. • To stop the cooking time: Example for 13 minutes at power 7: Action Zone selection Control panel Display press display [7] selected [0] and control light on Select << Timer >>> press key [13] [13] Deactivate the units slide on the "SLIDER“ to [ 0 ] [ 1 fixed ] [ 0 blinking ] Valid the units press display [ 10 ] [ 1 blinking ] [ 0 fixed ] Deactivate the tens slide on the "SLIDER“ to [ 0 ] [ 0 blinking ] [ 0 fixed ] Valid the tens press display [00] [00] • Automatic stop at the end of the cooking time: As soon as the selected cooking time is finished the timer displays blinking [00] and a sound rings. To stop the sound and the blinking it is enough to press the key [ 00 ]. • Egg timer function: Example for 29 minutes: Action Activate the hob Control panel press display [] press display [ CL ] Display zone control lights are on [00] Select<< Timer >>> Set the units slide on the "SLIDER“ to [ 9] [0 fixed ] [ 9 blinking ] Valid the units [ 0 blinking ] [ 9 fixed ] Set the tens slide on the "SLIDER“ to [ 2] [ 2 blinking ] [ 9 fixed ] Valid the tens press display [ 29 ] [ 29 ] After a few seconds the control light stops with blinking. As soon as the selected cooking time is finished the timer displays blinking [00] and a sound rings. To stop the sound and the blinking it is enough to press the display [ 00 ]. The hob switches off. Automatic cooking All the cooking zones are equipped with an automatic “go and stop” cooking device. The cooking zone starts at full power during a certain time, then reduces automatically its power on the pre- selected level. • Start-up: Action Zone selection Full power setting Automatic cooking Power level selection (for example “ 7 “) Control panel press display [0] selected slide on the "SLIDER" to [ 9] re-press on display “SLIDER“ [ 9 ] slide on the "SLIDER" to [ 7 ] Display [0] and control light on pass from [ 0 ] to [ 9 ] [9] is blinking with [ A ] [9] pass to [ 8][7] [7] is blinking with [A] • Switching off the automatic cooking: Action Zone selection Power level selection Pause function Control panel press [7] from the zone slide on the "SLIDER" Display [7] blinking with [A] [1] to [9] This function brakes all the hob's cooking activity and allows restarting with the same settings. • Startup/stop the pause function : Action Engage pause Stop the pause Control panel press [ S ] during 2s press [ S ] during 2s press an other touch or slide on the "SLIDER" Display displays [ II ] in the heating zone displays pause control light is blinking pause control light is off Recall Function After switching off the hob [①], it is possible to recall the last settings. • cooking stages of all cooking zones (power) • minutes and seconds of programmed cooking zone-related timers • Heat up function The recall procedure is following: • Press the key [] • Then press the key [ II ] within 6 seconds The precedent settings are activated. "Keep warm" Function This function allows to reach and maintain automatically a temperature of 70°C. This will avoid liquids overflowing and fast burning at the bottom of the pan. • To engage, to start the function « Keep warm »: Action Zone selection To engage To stop Control panel Press display [0] selected Press on key [ U ] on the “SLIDER“ Press on display [ U ] selected Slide on the "SLIDER" Display [ 0 ] to [ 9 ] or [H] [U] [U] [ 0 ] to [ 9 ] or [H] This function can be started independently on all the heating zones. When the pan leaves the cooking zone of the "Keep warm" function remains active during approximately 10 minutes. The maximum duration of keeping warm is 2 hours. Control panel locking To avoid modifying a setting of cooking zones, in particular during of cleaning the control panel can be locked (with exception to the On/Off key []). • Locking: Action Start Hob locking Control panel press on key [①] press simultaneously [ P ] and [0] from the front right zone display re-press on display [0] Display [ 0 ] or [ H ] on the displays no modification [L] on the displays • Unlocking: Action Start In the 5 seconds after start: Unlocking the hob Control panel press on key [①] Display [L] on the displays press simultaneously [ P ] and [ 0 ] or [ H ] on the displays [L] from the front right zone display press on key [P] no light on the displays Bridge Function This function allows to use the 2 cooking zones at the left at same time with the same features as a single cooking zone. Booster function isn't allowed. Action Activate the hob Activate the bridge Increase bridge Stop the bridge Control panel Press display [] Press on the 2 cooking zones left Slide on the "SLIDER " [ 1 to 9 ] or display [U] Press on the 2 cooking zones links Display [ 0 ] or [ H ] on the 4 displays [0] appears on the front zone [Π] on the rear zone. [ 1 to 9 ] or [U] [0] or [H] on the 2 zones