This article explains how to assemble the BIKW40-1 by Boretti.
Instructions d'installation
Le montage relève de la compétence exclusive de spécialistes. L'utilisateur est tenu de respecter la législation et les normes en vigueur dans son pays de résidence. How to fix the gasket: The gasket supplied with the hob avoids all infiltration of liquids in the cabinet. This installation has to be done carefully, in conformity of the following drawing. Stick the gasket (2) two millimetres from the external edge of the glass, after removing the protection sheet (3). Fitting - installing: • The cut out sizes are: Reference Worktop cut-out (mm) Width x Depth BIKW-40-1 366 x 466 • The piece of furniture or the support in which the hob is to be fitted, as well as the edges of furniture, the laminate coatings and the glue used to fix them, must be able to resist temperatures of up to 100 °C. • The mural rods of edge must be heat-resisting. • The hobs are classified as "Y" class for heat protection. Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear and tall units or a wall at one side. On the other side, however, no unit or divider must stand higher than the hob. • Ensure that there is a distance of 50 mm between the hob and the wall or sides. • Materials which are often used to make worktops expand on contact with water. To protect the cut out edge, apply a coat of varnish or special sealant. Particular care must be given to applying the adhesive joint supplied with the hob to prevent any leakage into the supporting furniture. This gasket guaranties a correct seal when used in conjunction with smooth work top surfaces. • Not to install the hob to the top of a not ventilated oven or a dishwasher. • To guarantee under the bottom of the hob casing a space of 20 mm to ensure a good air circulation of the electronic device. • To guarantee between the work top and the top of the drawer or oven a space of 5 mm to allow the exit of the air flow. • If a drawer is placed under the work, avoid to put into this drawer flammable objects (for example: sprays) or not heat-resistant objects. • The safety gap between the hob and the cooker hood placed above must respect the indications of the hood manufacturer. In case of absence of instructions respect a distance minimum of 760 mm. • The connection cord should be subjected, after building, with no mechanical constraint, such for example of the fact of the drawer. • The installation of the hob in no stationary sites (for example: boat) should be undertaken by specialists. Electrical connection • The installation of this appliance and the connection to the electrical network should be entrusted only to an electrician perfectly to the fact of the normative regulations and which respects them scrupulously. • Protection against the parts under tension must be ensured after the building-in. • The data of connection necessary are on the stickers place on the hob casing near the connection box. • The connection to the main must be made using an earthed plug or via an omnipolar circuit breaking device with a contact opening of at least 3 mm. • The electrical circuit must be separated from the network by adapted devices, for example: circuit breakers, fuses or contactors. Caution! This appliance has only to be connected to a network 230 V~ 50 Hz. Connect always the earth wire. Respect the connection diagram. Use the connecting cable that is attached to the device. The green / yellow wire correspond to the earth wire, the blue wire correspond neutral wire and the brown wire correspond to the phase. Mains Connection Cable diameter Cable Protection calibre 230V~1P+N 50Hz 1 Phase + N 3 x 2,5 mm² H05VV-F 16 A * H 05 RR - F
- calculated with the simultaneous factor following standard EN 60 335-2-6/1990 Caution! Ensure that you correctly attach the wires and the bridges and tighten the screws properly. Boretti cannot be held responsible for any incident resulting from incorrect connection or which could arise from the use of an appliance which has not been earthed or has been equipped with a faulty earth connection. Installation instructions The installation comes under the exclusive responsibility of specialists. The installer is held to respect the local legislation and standards. How to fix the gasket: The gasket supplied with the hob avoids all infiltration of liquids in the cabinet. This installation has to be done carefully, in conformity of the following drawing. Stick the gasket (2) two millimetres from the external edge of the glass, after removing the protection sheet (3). Fitting - installing: • The cut out sizes are: Reference Worktop cut-out (mm) Width x Depth BIKW-40-1 366 x 466 • The piece of furniture or the support in which the hob is to be fitted, as well as the edges of furniture, the laminate coatings and the glue used to fix them, must be able to resist temperatures of up to 100 °C. • The mural rods of edge must be heat-resisting. • The hobs are classified as "Y" class for heat protection. Ideally the hob should be installed with plenty of space on either side. There may be a wall at the rear and tall units or a wall at one side. On the other side, however, no unit or divider must stand higher than the hob. • Ensure that there is a distance of 50 mm between the hob and the wall or sides. • Materials which are often used to make worktops expand on contact with water. To protect the cut out edge, apply a coat of varnish or special sealant. Particular care must be given to applying the adhesive joint supplied with the hob to prevent any leakage into the supporting furniture. This gasket guaranties a correct seal when used in conjunction with smooth work top surfaces. • Not to install the hob to the top of a not ventilated oven or a dishwasher. • To guarantee under the bottom of the hob casing a space of 20 mm to ensure a good air circulation of the electronic device. • To guarantee between the work top and the top of the drawer or oven a space of 5 mm to allow the exit of the air flow. • If a drawer is placed under the work, avoid to put into this drawer flammable objects (for example: sprays) or not heat-resistant objects. • The safety gap between the hob and the cooker hood placed above must respect the indications of the hood manufacturer. In case of absence of instructions respect a distance minimum of 760 mm. • The connection cord should be subjected, after building, with no mechanical constraint, such for example of the fact of the drawer. • The installation of the hob in no stationary sites (for example: boat) should be undertaken by specialists. Electrical connection • The installation of this appliance and the connection to the electrical network should be entrusted only to an electrician perfectly to the fact of the normative regulations and which respects them scrupulously. • Protection against the parts under tension must be ensured after the building-in. • The data of connection necessary are on the stickers place on the hob casing near the connection box. • The connection to the main must be made using an earthed plug or via an omnipolar circuit breaking device with a contact opening of at least 3 mm. • The electrical circuit must be separated from the network by adapted devices, for example: circuit breakers, fuses or contactors. Caution! This appliance has only to be connected to a network 230 V~ 50 Hz. Connect always the earth wire. Respect the connection diagram. Use the connecting cable that is attached to the device. The green / yellow wire correspond to the earth wire, the blue wire correspond neutral wire and the brown wire correspond to the phase. Mains Connection Cable diameter Cable Protection calibre 230V~1P+N 50Hz 1 Phase + N 3 x 2,5 mm² H05VV-F 16 A * H 05 RR - F
- calculated with the simultaneous factor following standard EN 60 335-2-6/1990 Caution! Ensure that you correctly attach the wires and the bridges and tighten the screws properly. Boretti cannot be held responsible for any incident resulting from incorrect connection or which could arise from the use of an appliance which has not been earthed or has been equipped with a faulty earth connection.