This article covers the safety guidelines for the BTG-80 BTG-100 by Boretti.
General precautions
Please read this instruction handbook carefully before installing and using the appliance. This handbook must be kept in easy reach of the appliance for future consultation. If this ap- pliance is sold or transferred to another user, please give this handbook to the new user so that they can learn how to use it correctly and be aware of the various warnings This is a Class 3 appliance designed home use. This appliance complies with the following Directives: EEC 90/396 (Gas) EEC 89/336 (Electromag- netic Compatibility) EEC 2006/95/CE (Low Voltage) EEC 89/109 (Contact with foods)
- The appliance must be installed by a skilled and qualified installer, in conformity with sta- tutory legislation. This appliance is designed for use by adults. This appliance is not intended for use by persons (including children) with reduced or impaired physical or mental capabilities, or persons lacking experience and awareness, unless they are supervised or taught how to use the appliance by a responsible carer. Do not allow children to play with the appli- ance.
- Before powering the appliance, ensure that it is properly adjusted for the type of gas avai- lable (see "installation").
- Before carrying out maintenance or cleaning operations, disconnect the appliance from the power supply and allow it to cool.
- Ensure air is able to circulate around gas ap- pliances. Insufficient ventilation will lead to depletion of the oxygen in the air in the place of installation.
- In case of intense or prolonged use of the appliance, it may be necessary to increase ventilation, for example by opening a window or increasing the power of extractor fans, if present.
- Combustion products must be expelled from the place of installation through an extractor hood or extractor fan (see "Installation").
- For any replacements or alterations that may be required, contact an authorised Technical Assistance Centre and insist on the use of original spare parts. IMPORTANT: The product label, with the serial number, is affixed to the underside of the hob. The Manufacturer cannot be held responsible for damage to property or personal injury re- sulting from incorrect installation or improper, erroneous or unreasonable use of the appliance. Instructions for the installer Important notice: The operations indicated below must be car- ried out by qualified personnel only, in confor- mity with statutory legislation. The manufacturer declines all liability for injury to persons or animals or damage to property due to failure to comply with these prescrip- tions. Installation Installing the hob The appliance is designed to be built-in to a heat-resistant kitchen unit. Kitchen unit side walls must be able to wit- hstand temperatures of up to 75°C higher than room temperature, in accordance with Euro- pean regulations. It is permissible to install the appliance next to a kitchen cabinet extending above the worktop on one side only, either to the right or left. Any adjacent cabinet must be no less than 50 mm from the edge of the hob. The appliance must not be installed near inflam- mable materials, such as curtains, cloths, etc. Cut an opening in the top of the kitchen unit observing the dimensions shown in fig. 1, main- taining a distance of at least 50 mm between the edge of the appliance and adjacent walls. implemen- tation Model (mm) L(mm) D (mm) BTG-80 790 x 510 750 480 BTG-100 1000 x 400 950 365 ans of a separator, leaving a well space of at least 10 mm in depth. (fig. 2). If the hob is installed over an oven, precauti- ons must be taken to guarantee installation in accordance accident prevention standards (CEI-UNI-CIG). Pay particular attention to the position of the electric cable and gas supply hose: they must not touch any hot parts of the oven. Moreover, if the hob is installed over an oven without a forced cooling system, to en- sure adequate ventilation air vents must be provided with lower intake surface area of at least 200 cm² and upper outlet surface area of at least 60 cm². fig. 1 10 mm fig. 2 If the hob is to be installed beneath a wall- mounted kitchen cabinet, ensure there is a minimum clearance of 760 mm between the worktop and the underside of the cabinet. It is good practice to isolate the appliance from the cupboard below in the kitchen unit by me-