This article explains how to use the BTG-80 BTG-100 by Boretti.
Using the appliance - 5-burner version
The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. [ _ L J + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power set- ting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment: when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level; when the level is decreased from 9 to 1, the adjustment is progressive. Turning off a burner Briefly press the “+” and “-” buttons for the desired burner simultaneously. The power level indi- cator shows letter “H” indicating that the burner is still hot. This indication is cleared after a few minutes. Using the appliance - 4-burner version The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power setting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment:
--when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level;
--when the level is decreased from 9 to 1, the adjustment is progressive. 40 Using the appliance - 4-burner version The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power setting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment:
--when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level;
--when the level is decreased from 9 to 1, the adjustment is progressive. 40 Using the appliance - 5-burner version The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. [ _ L J + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power set- ting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment: when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level; when the level is decreased from 9 to 1, the adjustment is progressive. Turning off a burner Briefly press the “+” and “-” buttons for the desired burner simultaneously. The power level indi- cator shows letter “H” indicating that the burner is still hot. This indication is cleared after a few minutes. Using the appliance - 4-burner version The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power setting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment:
--when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level;
--when the level is decreased from 9 to 1, the adjustment is progressive. Using the appliance - 4-burner version The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power setting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment:
--when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level;
--when the level is decreased from 9 to 1, the adjustment is progressive. Using the appliance - 5-burner version The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. [ _ L J + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power set- ting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment: when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level; when the level is decreased from 9 to 1, the adjustment is progressive. Turning off a burner Briefly press the “+” and “-” buttons for the desired burner simultaneously. The power level indi- cator shows letter “H” indicating that the burner is still hot. This indication is cleared after a few minutes. Using the appliance - 5-burner version The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. [ _ L J + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power set- ting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment: when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level; when the level is decreased from 9 to 1, the adjustment is progressive. Turning off a burner Briefly press the “+” and “-” buttons for the desired burner simultaneously. The power level indi- cator shows letter “H” indicating that the burner is still hot. This indication is cleared after a few minutes. Using the appliance - 5-burner version The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. [ _ L J + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power set- ting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment: when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level; when the level is decreased from 9 to 1, the adjustment is progressive. Turning off a burner Briefly press the “+” and “-” buttons for the desired burner simultaneously. The power level indi- cator shows letter “H” indicating that the burner is still hot. This indication is cleared after a few minutes. Using the appliance - 5-burner version The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. [ _ L J + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power set- ting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment: when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level; when the level is decreased from 9 to 1, the adjustment is progressive. Turning off a burner Briefly press the “+” and “-” buttons for the desired burner simultaneously. The power level indi- cator shows letter “H” indicating that the burner is still hot. This indication is cleared after a few minutes. Using the appliance - 5-burner version The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. [ _ L J + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power set- ting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment: when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level; when the level is decreased from 9 to 1, the adjustment is progressive. Turning off a burner Briefly press the “+” and “-” buttons for the desired burner simultaneously. The power level indi- cator shows letter “H” indicating that the burner is still hot. This indication is cleared after a few minutes. Using the appliance - 5-burner version The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. [ _ L J + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power set- ting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment: when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level; when the level is decreased from 9 to 1, the adjustment is progressive. Turning off a burner Briefly press the “+” and “-” buttons for the desired burner simultaneously. The power level indi- cator shows letter “H” indicating that the burner is still hot. This indication is cleared after a few minutes. Using the appliance - 5-burner version The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. [ _ L J + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power set- ting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment: when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level; when the level is decreased from 9 to 1, the adjustment is progressive. Turning off a burner Briefly press the “+” and “-” buttons for the desired burner simultaneously. The power level indi- cator shows letter “H” indicating that the burner is still hot. This indication is cleared after a few minutes. Using the appliance - 5-burner version The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. [ _ L J + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power set- ting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment: when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level; when the level is decreased from 9 to 1, the adjustment is progressive. Turning off a burner Briefly press the “+” and “-” buttons for the desired burner simultaneously. The power level indi- cator shows letter “H” indicating that the burner is still hot. This indication is cleared after a few minutes. Using the appliance - 5-burner version The symbols printed above each burner control show the correspondence between the control and the burner. Standby mode After connecting the appliance to the power supply, it will perform a brief self-diagnosis routine and touch panel calibration (all displays and LEDs remain illuminated for a few seconds). When this procedure is completed the display will be blank. Switching on the hob To switch on the hob, hold the ON/OFF button for at least 2 se- conds. The appliance will switch on and the five burner displays will show power level 0, meaning that the burners are off. [ _ L J + _ Φ Lighting a burner To light a burner, hold down the “+” and “-” buttons on the control panel simultaneously for at least 1 second. After a few seconds, the selected burner will light and power set- ting 5 will be selected automatically. The associated indicator light will remain on as long as the burner is lit. All burners for which the timer has not been set will turn off automatically after 4 hours of continuous operation. Adjusting burner flame levels After lighting the burner, press “+” to turn up the power level and “-” to turn it down. For continu- ous variation of the power level hold down the “+” or “-” button and release it at the desired level. Power levels can be adjusted from 1 to 9. Burner response differs during upward and downward power adjustment: when the level is increased from 1 to 9, after the adjustment the burner first assumes power level 9 and then assumes the set level; when the level is decreased from 9 to 1, the adjustment is progressive. Turning off a burner Briefly press the “+” and “-” buttons for the desired burner simultaneously. The power level indi- cator shows letter “H” indicating that the burner is still hot. This indication is cleared after a few minutes.